GLD series belt type coal feeder fully enclosed coal feeder manufacturer promotion

Series belt type coal feeder fully enclosed coal feeder series belt type coal feeder belt type coal feeder feeder feeder
Series belt type coal feeder product introduction
Belt type coal feeder also Called feeder and feeder, series of belt-type coal feeders (divided into belt and A-belt, coal safety certificate number, appearance shown in the picture, belt patent number: ., A-belt patent number: .), are widely used in Coal feeding in various coal bunkers in coal, metallurgy, electric power and other industries is a rotating continuous coal feeding method. During production, users can adjust it (manual adjustment or hydraulic cylinder adjustment) without stopping the machine as needed, so that the coal feeding system can meet the requirements of high efficiency. , energy saving and environmental protection requirements, it is an updated product of the reciprocating coal feeder and vibrating coal feeder.
In addition to producing a series of standard belt coal feeders, our company also produces non-standard and extended belt coal feeders.
Structure features of series belt coal feeder
. Small operating power, low energy consumption, good economy
. Large coal feeding capacity, stable
3. Dynamic adjustment, stepless Speed regulation and adjustment are convenient
. Smooth operation, low noise, environmental protection
. Small wear, low maintenance, long service life
. High versatility of parts and easy installation and maintenance
> .Can replace other types of existing coal feeders.
Technical Parameters of Series Belt Coal Feeder
Model
Maximum Coal Feeding Volume
Power
Maximum Belt Speed
Machine Weight
/




/




/










Series belt coal feeder installation instructions
The coal feeder can It can be installed separately on site or as a whole.
When installing separately, first install the funnel frame at the mouth of the coal bunker, then install the box body, and then install other components such as the bottom frame.
During the overall installation, first install the funnel frame at the mouth of the coal bunker, then assemble all other components, and then hoist the overall structure and connect the connecting sections with bolts.
Testing and operation of the coal feeder
After the coal feeder is installed in place, start the motor without load to make the coal feeder operate without load. When no abnormality is found within a few minutes of idling, stop and check the temperature rise of the motor, reducer, drum and idler components. If everything is normal, check and tighten the relevant bolts and nuts again, then restart and slowly open the coal bunker. , so that the coal flow enters the coal feeder from small to large, so that the coal feeder can be put into normal operation.
Coal feeder inspection and maintenance
When the coal feeder is in use, a sufficient amount of coal should be stored in the coal bunker to avoid direct impact on the bottom plate when loading coal into the bunker.
After each month of continuous operation, check whether the parts are loose or abnormal.
Transmission parts need to be inspected every six months of continuous operation. If there are any abnormalities, repair or replace them immediately. .
All rotating parts are required to be filled with oil once a month and inspected once a quarter. The degree of damage to the bearings and seals is observed, and if any problems are found, replace them in time.
Maintenance of main components The reducer should be inspected every six months, and the rolling bearings and box should be cleaned or lubricated at the same time.
Electric motor: Carry out inspection and maintenance requirements according to the regulations of the electric motor.
Jining Dongda Mechanical and Electrical Co., Ltd. is located in Jining City, Shandong Province, the hometown of Confucius and Mencius. It is surrounded by scenic spots such as San Kong Holy Land, Mount Tai, Weishan Lake, and Shuibo Liangshan. It is adjacent to the Beijing-Shanghai Railway in the east and the Beijing-Shanghai Railway in the west. Beijing-Hangzhou Canal, adjacent to Ridong Expressway in the north, has convenient transportation and extends in all directions. The company has a registered capital of 10,000 yuan, an area of square meters, and total assets of more than 100 million yuan. The company has strong technical force, currently has many employees, including many professional and technical personnel, and has more than 3 sets of main production equipment and testing and testing instruments. It has formed a comprehensive capacity of annual production and sales of mining products exceeding 100 million yuan.