Fuzhou Zhigao gas stove after-sales service hotline "Entrepreneurial Awareness &╬じSafety Guarantee Maintenance"

Fuzhou Chigo gas stove after-sales service hotline "Entrepreneurial Awareness╬じSafety Guarantee Maintenance" Hourly toll-free customer service hotline: (/ /) Furong District, Yuhua District, Tianxin District, Kaifu District, Yuelu District, Fuzhou County, Dear Chigo Gas Stove Hello user, thank you for your support for our products. If this product causes inconvenience or trouble to you, please call the Fuzhou customer service hotline and we will serve you wholeheartedly as soon as possible. Chigo gas stove after-sales maintenance... new life... new taste... let you live a happy life endlessly... Fuzhou Chigo gas stove after-sales maintenance, Fuzhou Chigo gas stove repair phone number, Fuzhou Chigo gas stove repair... Chigo Gas Common faults of the stove include flame separation (flame loss), yellow flame (black smoke or red fire), backfire, poor fire transmission, uneven flame, small flame flameout, etc. , The igniter does not produce sparks. The piezoelectric ceramic of the natural igniter does not produce sparks, so that the stove plate cannot catch fire. There is a spark but it cannot ignite. The appearance of gas and liquefied gas stoves should be kept clean, and water droplets, oil stains, rust spots, etc. on the stove should be wiped off in time. This will not only save fuel but also extend the service life of the stove. . There is a fire, but you have to hold the switch with your hand, and it will turn off as soon as you turn it on. . The flame is not blue but yellow, and there is black smoke at the head of the fire. . Tempering, internal combustion, hot stove surface. . There is a spark but it does not ignite. There is gas but no spark. , Four-switch double-burner Teppanyaki stove The four-switch double-eye Teppanyaki stove has the opposite direction of opening and closing handles than the two-switch double-eye Teppanyaki stove, that is: when the handle is parallel to the stove surface, it is closed, and when it is perpendicular to the stove surface, it is fully open. . .How to deal with the switch tightness: You can remove the stove panel, use the panel or a small hammer to tap lightly on the top of the switch, and add a little lubrication to loosen it. .How to deal with small fires: Remove the burner, then light a fire on the nozzle, use thin iron wire to burn red, and dredge it inward until the fire power ejected makes a hissing sound. . Daily maintenance and precautions for electronic ignition stoves ① Since electronic ignition is composed of piezoelectric ceramics and metal to form a circuit to ignite, food that is usually burned should not drip onto the stove and keep the electrode part clean. ② Clean the blocked burner in time. ③ When ignition difficulty occurs, check whether the distance between the electrode and the stove body is too large, whether the ignition hole is unobstructed, whether the piezoelectric ceramic has failed (the fire is weak), whether the metal components have fallen off, etc. Otherwise, you should report to the relevant office for repair in time. (/ /) Common faults and troubleshooting methods of Chigo gas stoves 1. The ignition of the Chigo gas stove does not work (the Chigo gas stove does not light up), the pulse igniter has no battery or the battery voltage is insufficient rrr Install the battery or replace the battery, the gas source switch does not work Turn on or the air pressure is insufficient rrr Turn on the gas source switch or replace a new cylinder or ask the gas company if the gas is shut down. The ignition electrode is improperly distanced or contaminated rrr Adjust the ignition electrode to a reasonable distance and clean the electrode. The air pressure is too high, causing the air flow speed to be too fast. , impact spark rrr Adjust the opening of the air source switch appropriately to reduce the air pressure, the ignition nozzle is too large, the nozzle is too large, causing too much air flow, impact spark rrr replace the nozzle, the drum head is damaged, causing the ignition to be too close to the damaged part rrr replace The magnetic head and piezoelectric ceramic are aging rrr Replace the piezoelectric ceramic with a new one, the ignition output cable is not firmly connected to the porcelain head rrr Plug it in tightly and stick it firmly with glue or other glue, the output cable is damaged, causing super close ignition rrr Replace the cable or remove the damaged part Wrap it with insulating tape. If the impact block inside the switch assembly is worn or cracked, replace it with a new one. Pay attention to the correct installation position. If the micro switch of the pulse ignition assembly is in poor contact, repair or replace the micro switch, the front of the ignition nozzle or the memory of the ignition bracket. There are spider webs rrr Clear the spider webs, the hose is twisted or blocked rrr Clear the blockage, correct or replace the hose 2. The Chigo gas stove does not ignite (the Chigo gas stove does not ignite), the pulse ignition battery is not installed, or the battery is positive and negative If the pole is installed incorrectly, the battery should be installed correctly. The power cord has fallen off or is loose. The internal structure of the igniter is damaged. Replace the igniter and impact hammer, and reinstall the hammer. 3. The Chigo gas stove has abnormal flame, misfire or flame separation, the damper is too small, adjust the damper b, the nozzle is too small, expand the nozzle, there is air mixed in the gas pipeline, repeat the ignition action to drain the air, the pressure in front of the stove is too high , the main valve opening can be appropriately adjusted. For liquefied gas, professionals should be asked to adjust or repair the pressure regulator (the outlet pressure is too high). , backfire, strong wind blows the flame, avoid strong wind blowing directly to the flame b. The air pressure is too low, increase the opening of the valve, ask the air supply department whether to stop the air, seal the combustion, provide the appropriate amount of air, the damper is too large, Zhigao Gas stove repair, Chigo gas stove repair phone number, Fuzhou Chigo gas stove repair Chigo gas stove after-sales service phone number. Turn down the damper, unreasonable design, too large fire hole diameter, too large space, etc., the nozzle is too small or blocked, replace the nozzle or use Poke a needle to remove debris in the nozzle, and the fire cover is not in place. Adjust the installation position, fire cover, and burner aging, and replace the fire cover and burner. , black smoke or yellow flames, the damper is fully closed, open the damper appropriately b. There are spider webs in the ejector tube, remove the spider webs, the wrong stove model is selected, artificial gas is mistakenly used as a liquefied gas stove, the fire hole of the fire ring is blocked, clean it There are foreign objects in the fire hole of the fire ring and the nozzle hole of the stove. Clean the foreign objects. 4. If the Chigo gas stove leaks or the Hongri gas stove has gas odor, the hose is broken or not connected properly, replace the hose with a new one and fix it. b. The seal at the valve joint is aging, replace the sealing ring, or the valve fails for a long time, replace the valve and stove with a new one. If the head is not ignited, troubleshoot, re-ignite, flame out or remove the flame, clear out the flame (solve according to the previous method), universal joint is leaking, repair or replace the universal joint, the welding is not strong, there are blisters, replace or re- The welded tee pipe and the nozzle are not inserted into the injection pipe. Reinstall the nozzle, cylinder, angle valve or pressure regulator, and replace the cylinder or pressure regulator. 5. Other malfunctions of Chigo stoves, such as long open flames, assembly stuck and unrecoverable, replace the assembly b, valve core retaining spring falling off, repair or replace the assembly, assembly accuracy is poor, reassemble. , the flame is too small, the stove model is wrong, identify the model and replace it b. The flameout protection device is not fully opened, repair the flameout device, the three-energy tube is not suitable, re-carry out the technical demonstration, the switch position is not in a high fire state, adjust the switch position, If the hose is bent or flattened, adjust the hose. If the pressure is insufficient, check whether the pressure regulator is faulty for liquefied gas. If the flame of artificial gas (pipeline transportation) is too small under peak conditions, only one end can be used at this time. When the pressure is lower than If there is a water column, you should negotiate with the gas company. Chigo) Fuzhou Chigo gas stove after-sales service hotline "cannot catch fire/repair hotline (/ /)