Tractor with rotary tiller high quality rotary tiller

Tractor with rotary tiller High-quality rotary tiller
< A driven type with rotating blade teeth as the working part
< Soil tillage machinery
<, also known as rotary tiller. It has a strong ability to break soil. It can break the soil finely in one operation, mix the soil and fertilizer evenly, and make the ground flat, meeting the requirements of dry land sowing or paddy field planting. It is conducive to gaining farming time, improving work efficiency, and making full use of the power of the tractor. However, the coverage ability of stubble and weeds is poor, the plowing depth is shallow, and the energy consumption is large. Mainly used in rice fields and vegetable fields, it can also be used
.
Rotary radius of rotary tiller:
. Transmission mode: intermediate gear transmission
. Plowing depth:
. It is mainly composed of transmission shaft, suspension frame, frame, gear box and other components.
. /3/ r/3/ r/3/3 r/3/ r/3/
.
. Three, mechanical use
Instructions
. At the beginning of the operation, the rotary tiller should be in the elevated state, first combine with the power output shaft to increase the blade shaft speed to the rated speed, and then lower the rotary tiller so that the blades gradually penetrate into the soil to the required depth. It is strictly prohibited to combine the power output shaft or sharply lower the rotary tiller after the blade is inserted into the soil, so as to avoid bending or breaking the blade and increasing the load on the tractor.
. ． During operation, the machine should be driven as slowly as possible, which can not only ensure the quality of the operation, break the soil into fine pieces, but also reduce the wear of the machine parts. Pay attention to whether there is any noise or metal knocking sound from the rotary tiller, and observe the soil breaking and plowing depth. If there is any abnormality, the machine should be stopped immediately for inspection and operation can be continued only after troubleshooting.
. ． When turning at the edge of the field, it is forbidden to work. The rotary tiller should be raised to keep the blades off the ground, and the tractor's throttle should be reduced to avoid damaging the blades. When lifting the rotary tiller, the inclination angle of the universal joint should be less than 3 degrees. If it is too large, impact noise will be produced, causing premature wear or damage.
. ． When reversing, crossing field ridges and transferring plots, the rotary tiller should be raised to the highest position and the power should be cut off to avoid damage to the machine parts. If it is moved to a distant place, the rotary tiller must be fixed with a locking device.
. ． After each shift, the rotary tiller should be maintained. Remove dirt and weeds from the blade, check the tightening of each connection, add lubricating oil to each lubricating oil point, and add butter to the universal joint to prevent increased wear.
. 4. Mechanical adjustment
Instructions
. Left and right horizontal adjustment. Stop the tractor with the rotary tiller on flat ground for the first time, lower the rotary tiller so that the blade is 1 centimeter away from the ground, and observe whether the left and right blade tips are at the same height from the ground to ensure that the blade axis is consistent during operation and the plowing depth is even.
.
. ． Front and rear level adjustment. When lowering the rotary tiller to the required tilling depth, observe whether the angle between the universal joint and the first axis of the rotary tiller is close to the horizontal position. If the angle between the universal joints is too large, the upper pull rod can be adjusted to keep the rotary tiller in a horizontal position.
. ． Lift height adjustment. During rotary tillage operations, the angle between the universal joints cannot be greater than 3 degrees, and it cannot be greater than 3 degrees when turning at the head of the field. Therefore, when lifting the rotary tiller, special attention should be paid to the height adjustment of the available screws for adjusting the position of the handle by tightening the limit at the appropriate position of the handle. If the rotary tiller needs to be raised again, the power of the universal joint should be cut off.
. Our company mainly produces and sells: feed pellet machine, straw crusher, mower, walking tractor, multi-functional wheat seeder, corn seeder, large rotary tiller, turning plow, wood pellet machine, digger Pit machines, corn threshers, peanut harvesters, balers and other equipment
Special note: The machinery sold by the company has non-capital issues, and the buyer shall bear the full return freight
Company name:
Qufu City, Shandong Province
Lu Feng
Machinery Company
Contact Person
Sun
Manager
Contact Number:
Business
< br/> Company address: Yanshi Industrial Park, Yao Village, Qufu City, Shandong Province
Our company adheres to the business philosophy of quality first, reputation first, serves the majority of consumers, and sincerely welcomes merchants to visit us. Call to discuss cooperation!