Golid LED human body sensor lamp

Golid Human Body Sensor Lamp
>
Product Introduction
: Ordinary fluorescent lamps/tubes used in underground garages will consume electricity per year
< br/>Use left and right
Fluorescent lamps (/piece) use about 1 kilowatt-hour of electricity per year, and the latest infrared induction lamps from Glid Lighting
use only 1 kilowatt-hour of electricity per year. (See the table below)
Comparison between traditional single
bracket and light source and sensor
light bracket and light source
> < > Comparison items

> Traditional single
stand and light source

> with sensor
light stand and light source


< > Price

> Yuan

> Yuan


< > Power

>

> Full light, Twilight


< > Annual power consumption (based on full daylight, day)

> Degree

> Twilight Accounting for hours, the full-bright hour meter measures the degree


< > Annual electricity bill (Kunming commercial electricity yuan/degree)

> Yuan

> Yuan


< > Warranty period

> One year

> Two years


< > Electricity bill for two years

> Yuan

> Yuan


< > As can be seen from the above comparison, On the surface, the initial investment cost of using a sensor light stand is more (multiple at most), but after one year, the sensor light can save yuan, and the annual savings can completely cover the cost of purchasing lamps, which is equal to The lighting fixtures are installed for free, and after two years, you can still make a profit from installing a sensor light.
In addition, using induction lights can also save switching and wiring costs, save maintenance costs, etc., which is also a lot of money!


>This product uses the most advanced human body infrared detection sensor, with built-in ambient temperature compensation circuit and power supply voltage stabilization control circuit. The entire circuit has been optimized and designed, and each component is made of high-quality and high-precision materials. The induction is stable and recognized by many consumers. The products are sold at home and abroad. (Remarks: There are two types of induction fluorescent lamps (fully off after full brightness, and slightly bright after full brightness). Customers are advised to pay attention to the selection: the all-off type is a sensor that lights up after a delay of seconds when someone comes. Then it goes off completely and enters sleep standby (sleep mode). The power consumption is about watts), choose this kind of dimming type suitable for bathrooms, stairs, aisles, wardrobes, cabinets, etc. It will automatically enter the % (about watts) dimming low power consumption working state standby after the induction light is turned on for a few seconds. Choose this kind of application. In underground parking lots, garages, warehouses and other places where the light is relatively dark, but a little brightness is needed)
>Second product features:
>Automatic metering
:
Can measure the light according to the surrounding environment You can choose the standby brightness of the sensor light by using light or dark (the light can automatically sense when a person or car is coming and turn on fully, and after the person or car leaves, it will return to % or % dim lighting according to the set time. You can freely set the brightness to % or %) . Because the underground garage needs a little dim lighting to prevent it from looking eerie and scary.) It saves more than % electricity than a constantly bright lamp.
>Fully automatic sensor
:
The lights will turn on when people and cars are approaching, and the lights will go off when people and cars are leaving
:
>The optimized induction control design can realize that the lights will turn on when people are approaching. Automatic delay extinguishing, no need to turn off the switch, energy saving and worry-free.
>Humanized design
:
Easy to install, using advanced human body thermal infrared detection sensing technology, which is different from traditional common technologies such as voice-activated touch buttons. It is highly sensitive, anti-interference, and silent. It has the characteristics of fast response speed and long sensing distance. At the same time, it does not emit any type of radiation, the device consumes very little power, and is non-contact, which can protect people's health to the greatest extent and avoid accidental infection by germs.
>Energy saving and long lifespan
:
Ultra-low power consumption, ultra-long standby, super-sensitivity: ultra-high brightness lamps have a lifespan of more than 10,000 hours (years), effectively eliminating long-on loads. Save electricity and extend load life.
>Temperature compensation
:
Unique temperature compensation chip reduces the influence of temperature on the lamp sensing distance.
>Three applications:
> This product can be widely used in parking garages, warehouses, stairs, aisles, wardrobes, cabinets, etc. It can be used for new installations or for renovation and replacement of places where traditional lamps have been used. Modification is very easy. Just remove the ballast starter of the original lamp, connect the live wire of the power cord to one end of the lamp, and the neutral wire to the other end of the lamp.
>
>
>
>
>
>
>
>
>
>
>
>
>