Various specifications of NQG-4.8 internal combustion rail cutting machine

.Various specifications of internal combustion rail cutting machines
--Jinzhou Shuangxing# Twenty years of professional manufacturing
Contact person: Ms. Fu
Address: Song, Linghe District, Jinzhou City, Liaoning Province Slope
Fax -
Customer consultation
-- Striving to create the industry's leading brand # Jinzhou Shuangxing
. Internal combustion rail cutting machine_picture_manufacturer_price
Jinzhou Shuangxing Xing has recently launched many styles of road maintenance machinery with lower prices and better quality than those in the same industry. In terms of after-sales, regular return visits are implemented, mainly including the tamping machine series. Sleeper wrench series, rail puller series, rail drilling machine series, rail grinding machine series, rail gap adjuster series, square sleeper series, hydraulic rail puller series, hand tool series, line fastener series and other railway machinery products are welcome to use units and distribution units to pay attention!
.Internal combustion rail cutting machine_picture_manufacturer_price
.Internal combustion rail cutting machine is a kind of maintenance tool. It not only cuts rails quickly and with high quality, but also has little wear on the grinding wheel. It is locked by rail clamps, has a simple structure, is light in weight, is easy to operate, safe and easy to move. Suitable for public works maintenance, seamless line broken rail repair and rail cutting in long rail welding factories. When cutting the rail, the verticality tolerance of the rail cross section can be guaranteed. Moreover, the smoothness of the rail cross section is also very good.
.Technical parameters of internal combustion rail cutting machine
Power:
Number of revolutions:
Cutting grinding wheel: ~
Cutting time: pair/rail
Utilization of grinding wheel Rate:/Rail~times/Rail~times/Rail~times
Section accuracy: Verticality.~. Flatness:.~
Overall dimensions:
Overall machine quality:
. Internal Combustion Rail Cutting Machine_Picture_Manufacturer_Price
How to use
First, install the lamella grinding wheel. Before installing the lamella, check whether the lamella grinding wheel has cracks and whether it is deformed by moisture. Whether the two sides are flat and the surface is uneven, which may cause the incision to deviate. After installing the oblique and clamping discs, tighten the locking nut but the torque should not be too large to avoid crushing the thin grinding wheel.
Install the rail cutting machine on the rail and pull out the positioning rod installed on the fixture. At this time, the position indicated by the end surface of the positioning rod is the cutting position of the grinding wheel. Move the rail cutting machine to the preset cutting position as needed. Then make the inner surface (convex surface) of the fixture closely contact the top surface of the rail and the lower part of the rail palate and tighten the set bolts. The rail cutting machine is in working condition.
. Pull the joystick with one hand to keep the rail cutting machine above the rail, while holding the other joystick with the other hand to prevent the sheet grinding wheel from hitting the rail.
After installing the rail cutting machine, pull the starting handle to start the internal combustion engine. After the internal combustion engine is started, run at idle speed for no less than 2 seconds to check whether all parts of the machine are normal. If there are any abnormalities, shut down to eliminate them. Increase the throttle and observe whether the thin disc grinding wheel is running smoothly, whether it is deflected, and whether all parts are running normally. If any abnormality is found, the machine should be stopped to replace the grinding wheel or troubleshoot. Before cutting, adjust the throttle and damper to meet cutting needs.
When cutting, the feeding of the thin grinding wheel mainly depends on the dead weight of the rail cutting machine and the swing of the joystick. Therefore, when holding the joystick with both hands, do not exert downward force and swing the joystick rhythmically as needed.
During the cutting process, the joystick should be kept swinging back and forth and should not stop somewhere. When pinching occurs, slowly lift the lamella grinding wheel and continue cutting. If pinching still occurs, stop the machine to check the cause or replace the lamella grinding wheel. When re-cutting, the thin grinding wheel must perfectly match the original incision, otherwise the cutting position should be changed.
If the cut is tilted during the cutting process, the machine should be stopped to check the cause, eliminate the fault, or replace the thin grinding wheel, change the cutting position, and start cutting again.
Usually, the top of the rail is cut first, then the waist, and then the bottom until it is cut off.
When the thin grinding wheel is worn to a certain extent (the diameter of the grinding wheel is approximately less than 10 mm), it may not be possible to cut the rail from one side of the rail. At this time, the grinding wheel needs to be moved to the other side to cut the rail in half until it is cut. When the diameter of the grinding wheel is less than about 100% due to the reduction in linear speed of the grinding wheel, the wear of the grinding wheel will be accelerated. At this time, even if the rail is cut in half, it may not be completely cut off. It is recommended to replace the thin grinding wheel to avoid replacing the grinding wheel without cutting the rail, causing the new grinding wheel to not match the original cut.
.Internal combustion rail cutting machine_picture_manufacturer_price
Jinzhou Shuangxing after-sales service and delivery instructions
.Cost-performance explanation:
Under the same product quality conditions, our company will not reduce the performance , giving the lowest and most realistic price at the cost of changing product parts. (Product production configuration can be carried out according to customer requirements)
. Delivery instructions:
Delivery according to the supply period. If there are special circumstances that require early delivery, our company will organize personnel within a limited scope. We will increase production intensity and implement production, installation, commissioning, packaging and other processes to meet your company's requirements.
.Instructions attached to product delivery:
① Product manual and maintenance manual
② Product certificate
③ Instructions attached to purchased parts
④ Consumable parts and their list (Models vary depending on the source)
. After-sales service scope:
The product warranty period is years. If the product has quality problems during the warranty period, our company will provide the fastest repair without any charge. Outside the warranty period If parts need to be replaced, our company will only charge the cost.
. Tracking products:
Our company will have at least one technical follow-up visit every month after the product is sold to track the use of the product and record it so that any problems can be dealt with in a timely manner and strive to achieve customer satisfaction.
Jinzhou Shuangxing produces and sells the following products
☆Railway transportation: internal combustion tamping picks, tamping machines, hydraulic rail drilling machines, hydraulic rail drilling machines, manual rail drilling machines, rack type Track starter, hydraulic track starter, rail cutting machine, square sleeper, hydraulic rail straightener, rerailer, universal gauge ruler, rail grinder, square ruler, rail transport car, etc.
☆Track accessories: stoppers Plate, turnout, turnout accessories, turnout tie rod, track gauge ruler, track gauge ruler, track gauge ruler, track gauge ruler, anchor rod, anchor drill rod, pneumatic drill rod, turnout pad, track plywood, road stud, insulating plywood, Crossover switches, pads, composite rubber pads, track fasteners, track clamps, gauge pull rods, rail guard gussets, line gusset bases, insulated gauge rods, gussets, twist drill pipes, coal drill pipes, twist drills Rod, connecting sleeve, chain spreader, wind drill, anchor pallet, pallet, nylon baffle seat, manual switch, manual bender, bender, bending machine, rail pressure plate, fish tail plates, fishtail bolts, etc.
Jinzhou Shuangxing sales network Hebei, Shanxi, Inner Mongolia, Liaoning, Jilin, Heilongjiang, Beijing, Tianjin, Shanghai, Jiangsu, Zhejiang, Anhui, Fujian, Jiangxi, Shandong, Henan, Hubei, Chongqing, Sichuan, Guizhou, Yunnan, Shaanxi, Gansu, Ningxia, Xinjiang and other places.
Remarks: The above content has related product parameters and pictures provided by Jinzhou Shuangxing Railway Machinery Co., Ltd. for reference only. Specific products may have different sources due to different production batches. Please contact the sales staff for specific details.