Anti-violence rope hook set

Shandong supplies EOD rope hook set. EOD rope hook set manufacturer wholesales EOD rope hook set Sun Yaru
1. Product description
This rope hook set is the most ideal for EOD personnel when handling explosive materials. Disposal equipment. It avoids direct contact between EOD personnel and suspicious explosive objects, and transfers and identifies suspicious explosive objects through remote operation, thereby effectively ensuring the safety of EOD personnel. The rope hook tool set is equipped with various ropes, pulleys, fixing tools, clamps, suction cups, expansion rods, cat hooks and other tools, all of which can be assembled and used in conjunction with each other.
2. The main components include
, main rope reel
The main rope of 1 meter is wound around the reel, and the end of the rope is equipped with a detachable stainless steel spring hook. The reel is equipped with a crank handle. When taking up the line, hold the handle to turn the reel. After the line is taken up, the handle can be removed and inserted into the plastic sleeve next to the handle.
Note that this reel cannot be used as a winch when using the main rope to pull objects.
, Nylon rope with sleeve (white)
Nylon rope is made of multi-strand polypropylene yarn, with soft rope sleeves at both ends, and the rope buckle is braided with forks to prevent it from being opened easily. After the tied objects are tightened with a rope lasso, the main rope and fixed pulley can be used to pull the objects.
Technical Specifications
Diameter & Length Gauge
． Covered wire rope.
The steel wire rope is made of multiple strands of galvanized steel wire, with rope sleeves at both ends, and the rope buckles are riveted by stainless steel sleeves. When tying objects, ropes can be used to tighten the ropes, and the hooks should be hung on the ropes with protective rings.
Attention!
Steel wire ropes cannot be used to bind hard objects with sharp edges to avoid breaking the rope.
The steel wire rope cannot bear load when it is bent.
Steel wire rope is ferromagnetic.
Serial number
Rope diameter
Length
Weight
Load

.










. Rope grabber
The groove of the rope grabber is made of two tooth-shaped plates. It is formed by combining them. Please refer to the picture on the right for its usage. When putting down ropes and pulling suspected explosives, use this tool to avoid pulling the rope directly and slipping off.
． Hook The hook is made of stainless steel, non-ferromagnetic, has a rectangular cross-section, and has two shapes: single hook and double hook. The outer surface is spray-coated with yellow plastic.
Serial number
Hook shape
Overall dimensions
Hook mouth size
Connecting thread
Number of pieces

Single hook
* *



Single hook
**



Single hook
** < br/>


Double hook
**
*

． Powerful pliers are made of steel plates. The adjusting screw end is equipped with a lifting ring, and the size of the jaws is adjustable. According to the size of the clamped object, the size of the jaws should be adjusted in advance. The right-hand screw jaws become smaller, but not <, otherwise the clamping function will fail. The clamp can be locked after clamping the object, and it can be towed using rope pulleys and hooks.
Attention!
When the objects held by the pliers are hoisted, they must not collide with the pliers handle when swinging, otherwise the locking will easily fail and the object will fall off.
Attention!
Powerful pliers are ferromagnetic.
Technical data
Maximum jaw size and sub-lengthbr/> Minimum jaw size
. Sheep’s eye ring is equipped with long wood screws, which can be fixed on wooden objects by hand-tightening the eye ring As a fixed point, the number of eye circles installed on the woodenware depends on the strength. If the strength is large, ~
.The lifting ring is made of stainless steel, with connecting threads and spray plastic on the surface. It is connected with the stainless steel hook to make the hook a hook with a lifting ring.
The sling is composed of nylon braided straps and polyester rope. This sling is suitable for tying packages and cylindrical objects. The binding form is the same as the belt. Before lifting, hang the nylon rope sleeve on the main rope hook.
Technical information Bandwidth, length and weightbr/> Maximum load
Diameter of bundled objects
. Shackle lifting eye is made of stainless steel. The pin has threads on one end and can be removed after loosening to become a split hook. This lifting ring can be used in conjunction with the two fixed pulleys and clamping devices in this set of explosive disposal equipment. Especially when the pulley cannot be hung directly, this lifting ring can be used as a transitional connection.
Attention!
When connecting, be sure to tighten the thread of the pin before loading.
Technical Information Wide Penetration Bore Diameter. Maximum Load
. Wedge nails Wedge nails are made of chromium alloy steel and have high strength and toughness. They are available in two shapes: single hanging holes and double hanging holes. The double hanging holes are aligned with each other. Wedge nails can be wedged into the joints of wall bricks and other civil construction materials. They can become fixed points or pull piles in open areas, such as parking lots.
Attention!
Technical information
The wedge nails should be wedged into a solid and non-loose base.
Wedge nails are ferromagnetic.
． Brace
An adjustable-span crossbar braces between doorways or windows. There are two hanging holes on the pole for hanging pulleys or ropes. There are spring pins and micro-distance adjustment screws on the pole. There is a nylon support foot at both ends of the pole. Whether to use the support legs depends on the material and unevenness of the door frame or window frame. Depending on the height, if the wall is made of cement or brick and the surface is flat, support legs can be used at both ends of the support pole. If the wall is uneven or has a wooden structure, there is no need for support feet. Poke the needle bar at the end of the rod directly into the wall. The length of the three needle bars at the left end of the support rod is adjustable. The adjustment method is to use an inner hexagonal wrench with a size of Insert it into the screw hole, find the inner hexagonal hole of the needle bar and rotate it.
With one hand, press the column pin to be flush with the outer ring of the rod's casing. With the other hand, pull the inner tube to adjust the length of the rod slightly smaller than the width of the door frame or window and place it horizontally. Turn the fine-tuning screw left to gradually lengthen the rod until After the pad is flat against the frame surface, turn the screw left again to tighten the crossbar. When tightening the crossbar, you can use the handle rod to penetrate into the screw hole and rotate it to save effort.
Attention!
Before loading the crossbar, check it first, and then hang the pulley or rope after it is really firm.
Place the support poles relatively parallel to the doorway wall or window wall.
Technical information
Shortest dimension of strut
Longest dimension of strut
Stepless adjustment of length range~
Weight
When carrying span
． Sliding rod clamp
A sliding rod is equipped with two movable clamping arms. There is a screw on each clamping arm to adjust the angle between the arm and the crossbar. The right-hand screw can adjust the two clamping arms. The arms are brought together to clamp the clamping object, and the left-hand screw can be used to loosen the arms and remove the clamp. There are three holes on the sliding rod for installing removable lifting rings or pulleys. The screw hole at the end of the clamp arm can be installed with three types of clamping blocks (circular flat clamping block, shaped clamping block, shaped clamping block). The use of these three clamping blocks depends on the surface condition of the clamped body. For example, flat clamping blocks can be used for large surfaces, shaped clamping blocks for narrow surfaces or window frames, and shaped clamping blocks for cylindrical surfaces.
Technical information
Clamp arm opening size
Clamp arm depth
． Detachable rope pulley
The detachable rope pulley is composed of a hook, a wheel frame, a pulley, an elastic bead and a splint. This pulley is used with ball clips and ropes.
It is especially necessary to use this pulley when dragging suspected explosives from a hiding place to an open area at an incident site and requires multiple turns. Pulleys need to be set at turning points of the transportation route, such as doorways, windows, etc. At this time, use the support pole as a hanging point. Before towing the suspected explosive, install a ball-shaped clip on the rope at the appropriate position in front of the first pulley (the pulley closest to the explosive). When the clip is moved to the pulley (the suspected explosive at this time) The object is also dragged under the pulley) hits the splint and squeezes it away. At this time, the rope breaks away from the pulley and continues to be dragged. The second pulley becomes the main pulley again. Continue to move suspected explosives until they reach their destination.
Attention!
The tightness of the splint on the pulley squeezed open by the ball clip is adjusted by the elastic bumper. For the screws in the small holes on both sides of the right-hand pulley, the clamping plate becomes tighter and the left-hand screw becomes looser. If the splint is too tight, it will be difficult to release the rope; if it is too loose, when the ball clip is not in place, the rope may knock the splint apart and the rope may be released prematurely.
Technical information
Overall dimensions (length, width and thickness)
Pulley diameter
Applicable rope diameter~
Lifting weight
Weight
.With lock Fixed pulley
The pulley with lock is composed of hook, roller, wheel frame and lock. The pulley and lock (tooth-shaped plate) are made of nylon, and the wheel frame is made of hard aluminum plate. When using it, first stagger the roller splint to expose the lock, then move the tooth-shaped plate to increase the gap between it and the roller, and then Hang the main rope into the wheel groove, reset the tooth-shaped plate, restore the wheel plate to its original shape and lock it with a spring pin. When lifting, the main rope is pulled forward without obstruction. When the lifting reaches a certain height, stop pulling the rope and lean on the lifting object. Its own weight pulls the rope in the opposite direction and brakes on its own.
． Main lock
In the process of removing suspected explosives at the incident site, at certain turning points when it is difficult to use the support rod to hang the pulley (such as at the corner or near a large area of wall), wedge the wedge nail into the wall The main lock can be hung on the wedge nail hole, and the main lock can be directly inserted into the nylon rope to be used as a fixed pulley. The smooth outer surface will not cause excessive wear on the rope.
Before hanging the main lock, press the spring lever with your hand. If there is a gap in the main lock, hang it into the wedge hole, and then tighten the main lock.
. Posts
There are two types of post. One is with two mounting positioning pins at the end, which is the middle piece between the anti-fall hook and the long tie rod. The other is with Long slot, which is the middle piece connecting the anchor hook and the long pole.
Note that the post is ferromagnetic.
Technical data
Connection screw holes
Dimensions (with long slot (with double positioning pins))
. Cable block
Hook head made of aluminum The screw is installed on the block with the wire groove. Adjust the nut on the hook screw to clamp the block on any part of the rope. There is a ring at the end of the hook screw to tie the rope or hang the pulley.
. Ball clip
The spherical clamp is made of aluminum alloy. The two semicircular clamps are connected by a screw. The gap between the left-hand clamps is enlarged. Put the nylon rope into the notch inside, and then turn the clamps right to tighten the rope. Stuck. This piece is used in conjunction with the detachable rope fixed pulley. When the block moves to the fixed pulley, the splint of the detachable rope pulley will be squeezed open, and the rope will fall off naturally.
. Adhesive fixed plate
The adhesive fixing plate is made of a hard aluminum plate with a thickness of 0.000000000000000000000 and is square in shape with a round hole on the back and a sticker on the back. The fixing plate can be pasted on a flat, clean and non-porous surface at will. Such as walls, ceilings, facades , cabinets, desktops, etc. The holes on the board are for fastening things, and a piece of pasting board can be used as a fixed point.
Attention!
When pasting the fixing board, the dust on the surface of the attachment should be wiped clean , and stick firmly to use.
Technical data
Adhesive area
Weight
Fixed under ideal conditions, load
. Vacuum suction cup
The main body is Made of cast aluminum alloy, there is a hanging ring in the middle of the beam, and a rubber suction pad with a center distance of millimeters.
The vacuum suction cup must be adsorbed on a smooth, flat, airtight surface, such as building doors, glass, furniture, filing cabinets , vehicle doors, windows, etc. Before adsorption, lift the lever on each suction cup, place the disc flat on the suction body, and lower the lever to suction the main body. Each suction cup can be used as a focus point or fixed point.
Attention!
The suction cup should be adsorbed on a clean and oil-free surface. Pull it with your hands before applying force and wait until it is firmly sucked before use.
The suction cup can only be fixed and used at the moment, and must not be hung for a long time. Hang heavy objects.
During use, do not collide with the lever on the suction cup, otherwise the vacuum suction will be lost immediately.
Technical data
Suction cup diameter & number of suction cups Ring aperture circle&
Outside Outline dimensions, length, width and height
.Dustpan
When suspicious scattered objects are found at the EOD site, the dustpan can be dragged to the destination using hooks, ropes and pulleys.
Use a dustpan Before, first use velcro to connect the relevant parts, fold it into a dustpan shape, hang the main rope hook on the buckle tab, after use, uncover the velcro and fold it into a flat plate and put it into the box.
Technical data
Inner dimensions: length, width and height
. Anchor hooks Anchor hooks are divided into three types, three-hook shape and five-hook shape. The hook has barbs, which cannot be removed once it is anchored to the target. The anchor hook is equipped with a ring, which is attached to the anchor. Hang the main rope here in front of the target, then place the hook in the long slot of the connecting rod in front of the setting pole and send the anchor hook to
Anti-off hook
The anti-off hook is a kind of locking spring The hook is suitable for hooking soft packages such as packages of suspected explosives. This hook cannot be dehooked as long as the object is hooked and the door is closed by the locking spring. There is a ring on the hook, and the main rope hook can be hung here in advance.
Attention!
The anti-detachment hook is ferromagnetic.
Technical data
Outer dimensions
Large hook, small hook.
Drag weight, lifting weight
Large hook, small hook