Supply of remote-controlled car blocking roadblocks, portable car blocking devices, and manual tire spikes

Traffic blocking roadblock

Remote control automatic
/
Manual dual-purpose portable traffic blocking nail
Product instructions
Put the roadblock to the road traction device and open the two directions Turn on the side lock buckle to turn on the power switch of the traction device (the red button lights up to indicate standby mode).
Pull out the remote control antenna and press the forward button (expand the front nail strap to the required length and release the button.
To close, press the back button (rear side) and press the back button until it is almost there.
Note
The circuit board has a delay function. Be sure to grasp the advance amount during operation, otherwise it will cause damage due to strong inertia impact on the box.
When collecting the box, connect the traction device to the nail tape box. The places should match, then erect the box and press the locks on both sides.
Please choose a flat road environment during the laying operation.
When remote operation cannot be performed due to electromechanical failure, you can hold the traction device to pull the nail belt out, and complete the layout manually.
Precautions (please read the instruction manual carefully before use)
Because the nails are sharp, be careful to avoid injury during operation and maintenance.
Near the nail belt during layout and operation Special personnel must be on duty to avoid accidental injury to pedestrians, vehicles, etc.
During the deployment and interception, it is strictly prohibited for any person to appear within meters of the inertial direction of the intercepted vehicle and the spike belt to avoid personal injury caused by the vehicle losing control after a tire puncture and other reasons.
When the equipment is idle for a long time, it needs to be charged once.
The power switch must be turned off promptly after use to avoid damage to the battery due to excessive discharge.
It is strictly prohibited to drop or hit the equipment box artificially or maliciously.< br/> This product is an electromechanical product and is not completely waterproof. Please pay attention to waterproofing, moisture-proof and exposure-proof during transportation, use and storage.
When re-installing the nails, please be sure to put the rubber ring in place first The top of the nail shaft (nail base), otherwise the nail will fall off easily.
It is recommended to regularly maintain the nail belt, nail shaft and nails, remove dust, and oil the nail shaft to ensure that the equipment is in good condition.
General faults Judgment and maintenance
If a remote control failure occurs, please check according to the following steps
Check whether the power supply of the remote control is normal (whether the battery of the remote control needs to be replaced).
Check whether the power supply of the equipment box is normal. The lithium battery of the host machine is charged once normally and can be used for continuous remote control retraction and retraction for more than one time or continuous standby for more than one hour. If the equipment's working efficiency drops significantly, you should consider replacing it with a new battery.
Check whether the circuit board is normal (when the power is turned on, the circuit board indicates Whether the light is on or not).
If the nail strip (aluminum strip) cannot be retracted and retracted normally due to deformation, please manually adjust the deformed aluminum strip to straighten it to return to normal.
This product is an electromechanical product. If normal use cannot be restored under special circumstances, please contact the supplier and follow the instructions of professional technicians to troubleshoot. Non-professionals are strictly prohibited from disassembling by themselves.
Product specifications and indicators
Outer box dimensions.
Equipment weight in kilograms.
Remote control speed: unfold meters within seconds and retract meters within seconds
The required length can be freely selected.
Remote control range meters.
Nail lengthbr/> Charging rules The first three charges require enough hours each time. Continuous retracting and retracting operations for more than 10 times, and continuous standby for more than 10 hours. The charger indicates that charging is in progress when the red light is on, and charging is completed when the green light is on.
This product has a one-year warranty. (Damage caused by abnormal operation is not covered by the warranty)
Beijing Ruijing Tengda Security Technology Co., Ltd.
Contact person Liu Jixing
Contact number
Landline
Fax< br/> Company address: Yunjingli Store, Tongzhou District, Beijing