Tiantongwan Glass Door Installation Company

玻璃门：

1000

自动门：

100000

电动门：

10000000000000

Tiantongwan Installation Glass Door Company (Shunyi District Installation of Automatic Doors, Customized Glass Doors, Tempered Glass Doors, Customized Installation, Excellent Quality, Glass Door Repair Center specializes in installing and repairing all kinds of glass doors for offices, shops, and homes, with fine workmanship, clean exterior appearance, and overall Noble and generous, full of modernity. Construction technology
< (Positioning, laying out the top limit groove of the installation frame, installing the wooden bottom bracket with metal finish, installing the vertical door frame, installing the glass, installing the glass door leaf, upper and lower door clips, positioning and installation of the door leaf Glass door handle
< (Construction methods and technical measures
< (Positioning and setting-out: The glass door composed of fixed glass and movable glass door leaf shall be laid out and positioned in a unified manner. According to the design and construction drawings According to the requirements, release the positioning line of the glass door, determine the position of the door frame, and accurately measure the ground elevation, the elevation of the top of the door frame and the elevation of the middle horizontal frame.
< (The limit groove on the top of the installation frame: the width of the limit groove should be larger than the width of the glass The thickness is mm and the groove depth is mm. When installing, first draw out two edge lines of the metal decorative plate from the normal line, and then install the limit groove on the top of the door frame according to the edge line. Adjust the groove depth in the notch through the glue pad. Limit In addition to the wooden lining, the trough is made of m steel plate pressing, steel plate welding and aluminum metal profiles and other linings covered with stainless steel.
< (Install the wooden base with metal facing: first fix the square wood on the ground, Then use all-purpose glue to stick the metal veneer panel to the wood. The square wood can be nailed directly to the embedded wood bricks, or fixed through expansion bolt connection. If aluminum alloy square tubes are used, they can be fixed to the frame columns with aluminum angles. or use wood screws to fix it on the wooden bricks embedded in the ground.
< (Install the vertical door frame: Nail the square wood of the door frame with the center line of the bullet, and then use plywood to determine the shape and position of the door frame column. Finally, the metal decorative surface is wrapped. When wrapping the surface, the joint position of the decorative surface should be placed at the middle door position on both sides of the glass installation. The joint position must be accurate and ensure that it is vertical.
< (Installing glass: use glass The suction cup machine sucks the thick glass tightly, and then the person holds the suction cup handle to lift the thick glass plate and move it to the installation position. Then the upper part of the glass is inserted into the limit groove on the top of the door frame. Then the lower part of the glass is placed on the bottom bracket. The lower part of the glass Align with the center line, and the two sides of the edge just seal the seam of the metal veneer outside the door frame. It is required that the veneer joint is invisible both inside and outside.
< (Fixed glass: on the bottom bracket square wood Nail two small square wooden strips on the inside and outside to sandwich the thick glass in the middle door. The square wooden strips are about mm away from the glass panel. Then apply all-purpose glue on the square wooden strips and stick the decorative metal on the square wooden strips. < br/>< (Inject glass glue for sealing: Inject glass glue for sealing on both sides of the top limit groove and the bottom bracket opening, as well as at the seams between thick glass and frame columns. When injecting glue, seal as needed. Start from the end of the gap where the glue is injected, and pour it at a constant speed along the gap so that the glass glue forms a straight line with a uniform surface outside the gap. Use a plastic sheet to scrape off the excess glass glue, and wipe the glue trace with a cloth.
< (Glass Butt joints: When the fixed part of the glass door needs to be spliced together due to its large size, the butt joints must have a width of mm, and the edges of the glass plates must be chamfered. After the glass is fixed, inject glass glue into the joint gap. After filling, use a plastic sheet to smooth the glue on both sides of the joint between the glass plates so that the gap forms a clean, even straight line. Use a clean cloth to wipe off the glue traces on the glass surface.
< (Installation of movable glass door leaf: Before installing the door leaf, the floor spring and the positioning pin on the top surface of the door frame should be positioned and installed. The two must be coaxial. Use a hanging vertical line to check during installation to ensure that the floor spring rotation axis is in line with the positioning pin. The center lines of the positioning pins are on the same straight line.
< (Install the upper and lower door clips of the glass door leaf: Install the upper and lower metal door clips on the upper and lower ends of the glass door leaf respectively, and measure the height of the door leaf. If the upper and lower edges of the door leaf are far from the door If the gap between the horizontal frame and the ground exceeds the specified value, that is, the height of the door leaf is not enough, you can place wooden plywood strips at the bottom of the glass in the lower door clip. At the same time, insert small wooden strips into the gaps on both sides of the metal upper and lower door clips, tap them firmly, and then inject glass glue into the gaps between the small wooden strips, thick glass, and door clips.
< (Door leaf positioning installation : First, adjust the positioning pin on the door frame beam out of the beam plane mm with its own adjustment screw, then put the glass door leaf up, align the hole of the rotating pin connector in the door clip under the door leaf with the rotating pin of the floor spring, and Rotate the door leaf and insert the hole into the pin. Then turn the door leaf so that it is at right angles to the door frame beam. Align the hole of the rotating connector in the door clip on the door leaf with the positioning pin on the door frame beam, and adjust the adjusting screw of the positioning pin. Insert the positioning pin into the hole about mm.
< (To install the glass door handle, the handle hole on the all-glass door leaf is usually processed when cutting the glass. When the handle connection part is inserted into the hole, it should not be too tight and should be slightly loose, such as If the insertion is too loose, you can wrap the insertion part with soft tape. Before installation, apply a little glass glue on the part where the handle is inserted into the glass. When assembling the handle, make sure its root is close to the glass and then tighten the fixing screw to ensure that the handle is not loose. .