Supply ZG-13 electric rail drilling machine universal electric rail drilling machine

' Supply Z-type electric rail drilling machine universal rail drilling machine
'
' China's railways have a history of more than a hundred years. Over the past hundred years, the means of railway track maintenance have evolved with the development of my country's railways. The rapid development of China's railway road maintenance methods is also changing with each passing day. From the initial purely manual maintenance to small machinery to large machinery, it can also be said that the history of China's railway road maintenance methods is the epitome of the history of my country's railway development. Jining Hengwang Industrial and Mining Machinery Co., Ltd. is also constantly updating its products and improving its services under the trend of railway science and technology development. If you have any questions, you can call: Xiao Guo will answer you at any time!
'
' ※Product introduction
'
' Drilling range ФФm
'. Power is.
. Spindle speed r/
' The installation time is. The unloading time is
. The drilling time is.
'The stroke is not less than mm
.Aperture deviation.
'Aperture roughness.Above
.Overall dimensions mmmmmm
.The weight of the whole machine
.The drill bit adopts Standard straight handle twist drill
. Universally used for rails, especially suitable for /m rails
1. Scope of application
The Z-type electric rail drilling machine is a special drilling machine for railway electrical conductors. It is an ideal rail drilling tool. It is suitable for railway laying, line maintenance and emergency repair, especially drilling operations in areas and areas with power and electricity. It can be applied to /m/m rails of various specifications, especially /m rails.
2. Features
This machine adopts electric motor.
.This machine adopts the transmission method of ruler reduction gear, and uses a universal drill bit to maximize the cutting power. Fast speed, high efficiency and low noise.
.This machine has advanced design, reasonable structure, convenient maintenance, small size and light weight.
.The clamping rail part of this machine adopts two sets of four-link clamping mechanisms, which are flexible in loading and unloading, firm and reliable in clamping, and work smoothly.
.This machine uses profiling blocks for positioning. The corresponding profiling positioning blocks (positioning blocks are accessories of this machine) can be replaced for various types of rails, so the positioning is accurate.
3. Operating Procedures
Before use:
First check whether the power cord of the motor is broken or leaking. Turn on the power of the motor and observe whether it operates normally without load for half a minute.
.Is the gearbox lacking lubricating oil?
.Select the positioning block with the same type as the rail to be drilled, and install it at the corresponding position on the drilling machine fixture.
.Turn the feed handle clockwise, first retract the spindle to the end, and then install the ground drill bit into the drill chuck and lock it.
.In operation
.Place the clamp on the top surface of the rail, adjust the appropriate length of the jack wire, and press down on the clamp handle to lock. If the locking strength is not enough, turn the jackscrew handle clockwise until it is locked.
. Turn on the power of the motor and let it idle for a second. When the motor runs smoothly and there are no abnormalities, rotate the handle counterclockwise. When the drill bit enters the turning state, water is injected for cooling. To prevent the drill bit from burning blue.
. After drilling through, stop water injection, quickly turn the handle clockwise, move the spindle to the final stop, and turn off the motor. Lift up the clamping tool's pressure handle, detach the entire machine from the track, and complete the operation.
'
'
' ※Company Introduction
' Jining Hengwang Industrial and Mining Machinery Co., Ltd. is located in the charming city of Jining, the hometown of Confucius and Mencius and the capital of canals, and is adjacent to the Oriental Holy City Qufu in the east. , it borders the historic Beijing-Hangzhou Grand Canal to the west, Qilu Lingxiu Weishan Lake to the south, and Mount Tai, the most famous of the five mountains, to the north. The company was established in 2001 with a registered capital of RMB 10,000 and currently has more than 100 employees. It specializes in operating rock drills, rock drills, shotcrete machines, support equipment, scraper accessories, rail equipment and other mining equipment and accessories according to market needs. The company adheres to the business philosophy of providing convenient services to customers, creating development opportunities for employees, and the entrepreneurial spirit of being enterprising and enjoying success. We warmly welcome new and old friends from all walks of life at home and abroad to negotiate trade, create great causes and create brilliance together.