Guiyang Siemens gas stove after-sales maintenance service phone number?

Guiyang Siemens gas stove after-sales maintenance service hotline? Guiyang Siemens gas stove repair Siemens gas stove repair Siemens gas stove after-sales maintenance
Guiyang Siemens gas stove after-sales maintenance service hotline ①△② (Siemens gas stove manufacturer maintenance) Guiyang office repair acceptance hotline ①①△②
Company Guiyang Hongxin Home Appliance Repair Address Yunyan District Contact Manager Wang Telephone Mobile Email @Siemens Gas Stove Electrical Appliances)
Siemens Gas Stove Repair) Guiyang Siemens Gas Stove After-sales Service Customer Service Center |? Dedicated? Repair Station ╬╬ Customer Service Center |
Guiyang Siemens gas stove after-sales service hotline ①△② (Siemens gas stove manufacturer maintenance) Guiyang office repair acceptance hotline ①①△②
Service procedures Telephone repair on-site inspection, accurate quotation, repair, recovery and warranty.
Safety certification, standardized repairs, and formal maintenance. The accessories are authentic and come with a warranty.
Service target Service defects, customer satisfaction, as long as you call the company's hourly repair hotline ①△② Guiyang Siemens gas stove after-sales service phone number, our company will serve you wholeheartedly as soon as possible!
★ Guiyang Siemens gas stove after-sales service Maintenance center Guiyang maintenance phone number ①①△②
The ignition does not work (the ignition does not catch fire)
The pulse igniter has no battery or the battery voltage is insufficient. Install the battery or replace the battery.
If the gas source switch is not turned on or the air pressure is insufficient, turn on the gas source switch or replace the cylinder with a new one or ask the gas company if the gas is cut off.
. The distance between the ignition electrode and the sensing electrode is improper or contaminated. Adjust the ignition electrode to a reasonable distance and clean the electrode.
If the air pressure is too high, causing the air flow speed to be too fast, adjust the opening of the air source switch appropriately to reduce the air pressure.
. The ignition nozzle is too large. The nozzle is too large, causing too much air flow and impacting the spark. Replace the nozzle.
, The drum head is damaged, causing the head to be replaced by ignition very close to the damaged part.
. The ignition output cable is not firmly connected to the porcelain head. Plug it in tightly and use glue or other glue to stick it firmly.
If the output cable is damaged, resulting in a close fire, replace the cable or wrap the damaged area with insulating tape.
If the impact block inside the switch assembly is worn or broken, replace it with a new one. Pay attention to the correct installation position.
. If the micro switch of the pulse ignition master process has poor contact, repair or replace the micro switch.
If there are spider webs in front of the ignition nozzle or in the ignition bracket, remove the spider webs.
If the hose is kinked or blocked, remove the blockage and correct or replace the hose.
2. Ignition failure (no ignition)
, The pulse ignition battery is not installed, or the positive and negative poles of the battery are reversed. The battery should be installed correctly. If the power cord falls off or is loose, or the internal structure of the igniter is damaged, replace it. Ignition, hammer, reinstall hammer.
3. Abnormal flame
Flame loss or separation, the damper is too small, adjust the damper, the nozzle is too small, expand the nozzle, there is air mixed in the gas pipeline, repeat the ignition action to drain out the air, the stove If the front pressure is too high, the main valve opening can be adjusted appropriately. For liquefied gas, professionals should be asked to adjust or repair the pressure regulator (the outlet pressure is too high).
, backfire, strong wind blowing the flame, avoid strong wind blowing directly to the flame, the air pressure is too low, increase the opening of the valve, ask the air supply department whether to stop the air, seal the combustion, provide the appropriate amount of air, the damper is too low Large, turn down the damper, unreasonable design, too large fire hole diameter, too large space, etc., the nozzle is too small or blocked, replace the nozzle or use a needle to clear the debris in the nozzle, the fire cover is not in place, adjust the installation position, fire The cover and burner are aging, replace the fire cover and burner.
, black smoke or yellow flame, the damper is fully closed, open the damper appropriately, there are spider webs in the ejector tube, remove the spider webs, the stove model is wrongly selected, artificial gas is mistakenly used as a liquefied gas stove, the fire ring fire hole If it is clogged, clean the fire hole of the ignition ring and the nozzle hole of the stove. If there is any foreign matter, clean it.
4. If there is air leakage or gas odor, the hose is broken or not connected properly, replace the hose with a new one and fix it, the seal at the valve joint is aging, replace the sealing ring, the valve fails for a long time, replace the valve with a new one, the burner does not ignite, Troubleshoot, re-ignite, de-fire or remove the flame, clear out the de-fire (solve according to the previous method), universal joint leakage, repair or replace the universal joint, weak welding, blisters, replace or re-weld the tee pipe , the nozzle is not inserted into the injection pipe, reinstall the nozzle, cylinder, angle valve or pressure regulator, and replace the cylinder or pressure regulator.
5. Other phenomena
There is a long open flame, the assembly is stuck and will not recover, replace the assembly, the valve core circlip falls off, repair or replace the assembly, the assembly accuracy is poor, and reassemble.
, the flame is too small, the stove model is wrong, identify the model, replace it, the flameout protection device is not fully opened, repair the flameout device, the three-energy tube is not suitable, re-carry out the technical demonstration, the switch position is not in the high fire state, adjust If the switch position, hose is bent or flattened, adjust the hose, if the pressure is insufficient, check whether the regulator is faulty for liquefied gas. For artificial gas (pipeline transportation), if the flame is too small under peak conditions, only one end can be used at this time. Contact the gas company if the pressure is below the water column. Guiyang Xianke gas stove after-sales maintenance center Guiyang maintenance phone number ①①△②