CDH-C20 plug-in sliding stopper price, plug-in sliding stopper manufacturer

Plug-in sliding car stop
Price
,
Plug-in sliding car stop
Manufacturer
Car stop
Manufacturer
, Sliding car stop
Purpose
, plug-in sliding car stop, sliding train stop, plug-in sliding car stop
, plug-in sliding car stop quotation
,
China Railway plug-in sliding blocker
Have you installed a train blocker on your track? Have you installed the China Coal Car Blocker? Not installed yet? Aren't you afraid of inspection? I heard that the inspection of car brakes is very strict recently. Do you want a car brake that is easy to install and cheap? Then quickly pick up your phone and dial one
eight Lu Lu Ling Qi Lu Yi Wu Lu San to order!
The car stopper is a safety device installed at the end of the railway to prevent the vehicle from hitting the car stop when it slips away. Direct supply from the manufacturer, quality guaranteed. The stopper is an improved version of the stopper. It has a reasonable structure, good braking force, and a plug-in connection method between the support arm and the brake rail. It is easy to install, easy to maintain and reset.
Product structure and working principle of plug-in sliding stopper
The stopper consists of a main frame and two pairs of boosters, with a full length.
Installation methods and requirements for plug-in sliding stoppers
The technical conditions of the line should comply with the public works standards, and the track gauge is.
. The car stopper should be installed on the last section of rail at the end of the end line, close to the rail joint and where there is no fish plate. There should be a certain distance between the car stopper and the end of the end line. The greater the distance, the better the braking effect. .
, Installation method
① Place the left and right arms on the basic rail, and connect them to the support with the arm pins.
② Lift the support arm and place the spring seat, leaf spring and bearing seat in sequence on the basic rail below the shoe type fastener.
③Clamp the shoe block with the brake rail, and also clamp the rail head of the basic rail, and then use three bolts to attach the brake rail. Note that the two outer bolts must pass through the support frame, and the bearing seat should be located in the center of the pressure hole.
④The train stopper uses front and rear cross beams and upper and lower inclined beams to connect the four lower legs of the two arms. The overlapping form is shown in the figure. The middle and four corners of the two inclined beams are tied with pins. After completing the above initial installation, tighten all bolts.
⑤The installation of the booster is to place the spring seat, leaf spring and bearing seat in sequence on the basic rail, and then use the two booster brake rails to sandwich it in the middle, and also clamp the rail head of the basic rail , and tighten the brake rail with two bolts. The first pair of boosters is millimeters away from the main frame, and the second pair of boosters is millimeters away from the first pair, parallel to each other, and the error does not exceed millimeters.
⑥ Use a pressurizer to pressurize each spring plate of the train stopper. Insert the shaped pressurizing fastener into the gaps on both sides of the bearing. Align the head of the pressurizing screw rod installed on the center nut of the pressurizer with the pressurizing block and hang it. The pressurized rail bottom plates on both sides are hooked on the basic rail bottom plate and tightened with nuts. Use a long iron rod to twist the pressurizing screw and drive the wedge iron between the bearing seat and the leaf spring so that the gap between the leaf spring and the spring seat is rice.
⑦Install the signboard on the support.
⑧After each installation, position marks should be painted on the rail waist to facilitate daily inspection to see if the train stopper has been damaged.
Product technical indicators
The total horizontal resistance of the car stopper is not less than.
The maximum collision speed allowed for a vehicle to collide with a vehicle barrier is/.
The center of the buffer rubber plate is higher than the basic rail surface.
Car stop, sliding car stop, plug-in sliding car stop, sliding train stop, plug-in sliding car stop
Contact person
Manager Wang
Mobile number
/>


Contact
Telephone



Number

Company Name Zhongmei Mining Materials Co., Ltd.