[Suzhou Guanyu] Supply Japan Expo magnetic pump_NH-403PW-F

NH-403PW-F：

40*50

功率：

0.37-11KW

重量：

50

Magnetic pumps are widely used in petrochemical, pharmaceutical, electroplating, environmental protection, water treatment, film, television, printing, national defense and other departments for pumping flammable, explosive, toxic and precious liquids due to their fully sealed, leak-free and corrosion-resistant characteristics. They are ideal for creating a leak-free, pollution-free civilized workshop and civilized factory. ideal pump. The following matters should be considered during the installation process of the magnetic pump: Place the unit on the foundation, place a pair of wedge pads between the bottom plate and the foundation, and adjust the wedge pads to align the level of the pump. After adjustment, tighten the anchor bolts.
The pump and motor should be inspected before installation. All parts should be intact and there should be no debris in the magnetic pump.
Foundation dimensions: Make a concrete foundation and bury the anchor bolts at the same time.
The suction and discharge pipeline of the force pump should be supported by a bracket, and the magnetic pump cannot be used for support. The diameter of the inlet and outlet pipes should be consistent with the diameter of the pump inlet and outlet.
After the installation is completed, finally turn the magnetic pump coupling by hand to check whether there is any friction. If the rotation is easy and even, the installation is complete.
The pump is strictly prohibited from pumping media containing particles and easily crystallized. It is not allowed to operate continuously with the discharge port closed, and the minimum flow rate must be maintained.
To prevent debris from entering the magnetic pump, a filter should be installed at the inlet, and the filtering area should be greater than ~ times the cross-sectional area of the pipeline.
When the viscosity is too high, the performance and power of the magnetic pump will change. Please follow the instructions for details.
It is necessary to ensure that the installation height of the magnetic pump complies with the NPSH of the pump, and consider the pipeline loss and medium temperature.
Introduction to the advantages of magnetic pump
Magnetic pump is a kind of non-contact torque transmission through magnetic transmission and magnetic coupling, thereby replacing dynamic seal with static seal, making the pump completely leak-free. Since the magnetic rotor in the pump shaft is completely sealed by the isolation sleeve of the pump body, the problem of leakage, leakage, and leakage is completely solved, and the potential safety hazard of leakage of flammable, explosive, toxic, and harmful media through the pump seal in the refining and chemical industry is eliminated, effectively ensuring the physical and mental safety of employees. Healthy and safe production.
Compared with centrifugal pumps that use mechanical seals or packing seals, magnetic pumps have the following advantages: The shaft changes from a dynamic seal to a closed static seal, completely avoiding medium leakage.
Requires independent lubrication and cooling water, reducing energy consumption.
Coupling transmission becomes synchronous drag, without contact and friction. It has low power consumption and high efficiency, and has a damping and vibration reduction effect, which reduces the impact of motor vibration on the pump and the impact on the motor when cavitation vibration occurs in the pump.
When loading, the inner and outer magnetic rotors slip relative to each other, which protects the motor pump.
When the driven part of the magnetic actuator operates under overload or the rotor is stuck, the main and driven parts of the magnetic actuator will automatically slip off to protect the pump. At this time, the permanent magnets on the magnetic actuator will produce eddy magnetic losses under the action of the alternating magnetic field of the active rotor, causing the temperature of the permanent magnets to rise and the magnetic actuator to slip and fail.
Expo Magnetic Pump Mainland Distributor,
Series Fiberglass Fiber Reinforced
Small magnetic drive pumps suitable for OEMs
OEMs and general applications.
The flow rate in this mode is up to cm/min.
Improve ceramic bushings and bearings as standard wear-resistant parts to increase service life.
Standard fittings for hose threads or kits.
Series ordinary type
Small magnetic drive pump suitable for semiconductors
Using polyethylene to naturally connect the bottom end and ceramic silicon material bearings and bearings, these pumps can be used in semi-body applications.
Mode, flow rate up to liters/minute.
Standard fittings that can be adapted to hose threads or kits.
Series carbon fiber reinforced type
Small magnetic drive pump suitable for transporting hazardous chemicals
Irrigation end material, suitable for transporting highly hazardous chemicals.
Mode, flow rate up to liters/minute.
Standard fittings that can be adapted to hose threads or kits.
Series fiberglass filled polypropylene type series natural polyvinylidene fluoride material series carbon fiber filled type
Microcomputer control, DC brushless motor, solid flow rate and variable flow rate magnetic drive pump. Magnetic drive pump equipped with DC brushless motor, printed circuit board and variable flow speed controller. Materials are available or meet different needs. Able to accommodate external milliamp current changes to maintain constant flow and head for varying pH values. The motor efficiency is twice that of AC motors. save space.
Series
Magnetic drive pumps for general use
OEMs and their general applications.
This form changes the flow rate up to liters/minute.
Suitable for hose thread and flange connections.
Polypropylene pouring material reduces costs.
Series of polytetrafluoroethylene
Magnetic actuator for transporting hazardous chemicals
Polyethylene pouring body material suitable for hazardous chemicals.
This model has a maximum flow rate of liters/minute.
Suitable for hose thread and flange connections.
Series
General purpose magnetic drive pumps
Polypropylene pouring material.
A variety of models, with flow rates up to liters/minute and lift meters.
It can transport many types of chemicals, and the maximum temperature can reach ℃.
Suitable for international electrician standard motors and power.
Suitable for flange connection.
Some models
Japan Expo magnetic pump
Japan Expo magnetic pump
Japan Expo magnetic pump
Japan Expo magnetic pump
Japan Expo magnetic pump
Japan Expo Magnetic Pump
Japan Expo Magnetic Pump
Japan Expo Magnetic Pump
Japan Expo Magnetic Pump
Japan Expo Magnetic Pump
Japan Expo Magnetic Pump
Japan Expo Magnetic pump
Japan Expo magnetic pump
Japan Expo magnetic pump
Japan Expo magnetic pump
Japan Expo magnetic pump
Japan Expo magnetic pump
Japan Expo magnetic pump
Japan Expo Magnetic Pump
Japan Expo Magnetic Pump
Japan Expo Magnetic Pump
Japan Expo Magnetic Pump
Japan Expo Magnetic Pump
Japan Expo Magnetic Pump
/> Japan Expo Magnetic Pump
Our company has long-term stock of Expo Magnetic Pump, welcome to call us!