Ruijin CZDLY-70(A) vertical fully hydraulic grass support pad forming machine

Ruijin vertical fully hydraulic straw mat forming machine strip type straw mat product forming machine is specially designed to meet the technical requirements and standards of Shanghai Railway Bureau's straw mat products for railway transportation. Implement standards. Special strip-shaped grass support pad product production equipment is developed and produced according to the Shanghai Railway Freight Number Document and the steel product transportation standards of Maanshan Iron and Steel Company and several major steel plants.
Safety precautions for the vertical fully hydraulic straw mat forming machine
In order to avoid accidents and accidental injuries, please allow professional operators to use this machine in accordance with relevant standards. Operators of hydraulic stations should ensure that when operating the machine Personnel on both sides can perform each operation only within a safe range.
When opening the reversing valve, it should be pushed into place at one time to prevent the press head from tilting.
Please rotate the motor in the direction marked on the oil pump.
Pay attention to the rising stroke of the oil cylinder to prevent damage to the sky beam.
The large presser feet on both sides of the machine should be firmly fixed.
No one may touch the operating valve of the operating machine without the consent of the operator.
When the machine is in operation, the forage throwers on both sides should retreat meters away from the working surface.
Precautions for use of vertical fully hydraulic straw mat forming machine
Persons who have not learned the structural performance and operating procedures of the machine are not allowed to operate the machine without authorization.
Each lubrication point of the machine should be filled with lubricating oil at least once per shift as required.
The hydraulic oil added to the tank should strictly use high-quality anti-wear hydraulic oil, which must be strictly filtered and sufficient oil should be maintained at all times. When the oil volume is insufficient, the oil should be added immediately.
The fuel tank should be cleaned and replaced with new oil every six months, but the first cleaning and filtering of the oil should not exceed a month. New oil that has been used once a month is allowed to be used again after strict filtration.
When there is a serious oil leakage or an abnormality occurs during work, the machine should be stopped immediately to analyze the cause and troubleshoot. Do not force the machine to operate while sick.
It is not allowed to repair or touch the moving parts with hands while the machine is in operation or during packaging. It is strictly forbidden to press materials in the material box with hands or feet.
The pressure pump cylinder operating valve and hydraulic pipe must be adjusted by experienced technical workers. If the machine is found to be faulty, it should be checked or updated immediately.
Technical parameters of vertical fully hydraulic straw mat forming machine
Forming specifications length, width and height
Motor power
Machine size
Machine weight
Vertical type Installation instructions for fully hydraulic straw mat forming machine
When installing the oil cylinder, please align the corresponding numbers with the screw holes on the sky beam in sequence and tighten the screws diagonally multiple times.
Please connect the oil pipe according to the corresponding number of the oil pipe. The oil pipe above should be connected to the oil valve. And check whether the ring is intact and the tubing wire head should be properly wrapped with raw tape in a clockwise direction.
When connecting the press head, a square piece of square wood should be placed on both ends of the lower groove plate to facilitate the insertion of the shaft between the cylinder connecting sleeve and the machine head connecting sleeve.
The large presser foot should be firmly fixed
The hydraulic oil in the oil tank should be high-quality anti-wear hydraulic oil, which must be strictly filtered and maintained with sufficient oil. If the oil volume is insufficient, enough oil should be added immediately
Type vertical Operating instructions for the fully hydraulic straw mat forming machine
This machine can be operated in a shift of three people or five people in a shift. When feeding, you should try to feed enough at one time or multiple times.
The stop point of the lower stroke of the press head should be 1 centimeter on the lower groove plate, which is the end point of the cylinder stroke. Please pay attention to closing the operating valve when operating.
This machine is an improved model that can produce both grass support pads and grass support pads.
When the pressure head reaches one centimeter, the operating valve should stop operating and press down. Operators on both sides pass through the iron wire and tie it with a tying hook.
After the binding is completed, the press head is raised and personnel on both sides open the side door handles and take out the support pads.
After taking it out, close the side door and repeat the operation.
Railway equipment and accessories
Oiler equipment Horizontal bending machine Internal combustion tamping machine Rail grinder Rail stretching machine Rail drilling machine Saw rail tamping machine Rail grinder Rail stretching machine Rail drill Hole machine, rail saw, motorized bolt wrench, track dialer, railway accessories.
Support type slotted anchor rock friction stabilizer seam pipe anchor pipe seam anchor pipe seam anchor pallet mesh metal roof beam metal long beam hinged roof beam transfer roof beam metal roof beam metal roof beam
Electro-hydraulic electric push rods, electric push rods, electric push rods, electro-hydraulic push rods, overall electro-hydraulic push rods, parallel electro-hydraulic push rods, electro-hydraulic push rods, mining hydraulic push rods, slide movers, hydraulic push rods and push rods. Manual pusher, moving slider, pusher
Company principles: Be honest, do things with heart, insist on unity, steady development, and work together to achieve success!
New and old customers are welcome to call for consultation. We promise to provide good products and the best service and never deceive new and old customers!
Company name Jining Yi'an Industrial and Mining Machinery Equipment Co., Ltd.
National toll-free number
Chen Qing
Manager Dong
Manager Liu
Manager Chen
Wang Manager
Telephone
Fax
Want Want Yi'an Industrial and Mining Machinery
Company address Jinyu Industrial Park, Rencheng District, Jining City
Machinery Factory No. 1 address Nanliu Industrial Park, Rencheng District, Jining City
The second machinery factory is located in Shilipu Industrial Park, Rencheng District, Jining City
The rubber and plastic factory is located in Jining High-tech Zone Industrial Park