Shenzhen Baoan Xixiang stone renovation Baoan Xixiang terrazzo polishing Baoan Xixiang waxing renovation

Shenzhen Baoan Xixiang stone renovation Baoan Xixiang terrazzo polishing Baoan Xixiang waxing renovation
First clean the original filling in the gaps between the stones
, and then use special stone
The seaming machine neatly cuts and slits the middle seams of the original stone installation to minimize the width difference between the gaps between the stones, and then fills them with marble glue that is close to the color of the stone. (Note: If the center seam has been done before, there is no need to re-open the seam).
Use marble glue that is close to the color of the stone itself
and perfectly adjust the color of the marble glue
so that it is fully close to the color of the original stone to improve the overall feel and achieve the most ideal effect Visual effect.
Fill the prepared marble glue
with it. Since the marble glue
will shrink to a certain extent after it is completely solidified, the marble glue
should be slightly higher than the The stone is horizontal
so that it will not be filled multiple times.
Use grinding and polishing discs
and grinding fillers
to make them become a horizontal plane with the stone
, increase the overall feeling of the stone, and solve the problem of high and low positions between gaps
, to prevent the gap from returning to black again. Use a granite renovation machine
with a special notch grinding disc
to carefully polish the notch so that it becomes a flat surface with the stone.
Grinding and polishing: Use a special granite
polishing machine
to grind the stone from coarse to fine using stone water-grinding discs
, making the floor as bright and smooth as new.
. Crystallization treatment: Use granite crystal powder and crystallization agent to polish with a crystal surface grinder. Under the heavy pressure of grinding, the stone and crystal powder undergo a comprehensive physical and chemical reaction under the action of high temperature to form a layer. Dense, hard crystalline protective layer. After crystallization, it can enhance the color and brightness
, and is also waterproof and oil-proof
*Marble
Mild renovation
If the surface of the stone is slightly scratched, a light renovation process can be used Refurbishment treatment. If there is old wax on the ground, remove the wax first, then use a diamond
water grinding disc
add water and polish for ten minutes. Note: add water during the polishing process to keep the ground moist, and use a water absorber
Suck away sewage to prevent sewage from contaminating the ground for the second time. Then replace 3 polishing discs
, diamond
water-grinding discs
, and polish them one by one using the above method. After all the renovation procedures are completed, wash with clean water and absorb the water on the surface of the stone. The light renovation of the marble is completed.
*Marble
Medium Renovation
When the stone surface loses its luster and cannot reflect the object at all but does not have deep scratches, the moderate renovation process can be used for renovation. Use 3 polishing discs
, diamond
water-grinding discs
to polish one by one. The polishing method and precautions are consistent with the above.
*Marble Deep Renovation
When the stone surface has holes, weathering, severe corrosion, complete loss of luster and deep scratches, the deep renovation process can be used for renovation. Before renovation, the holes must be repaired first. The method is as follows: clean the dirt in the holes first, then dry the stone, and use imported epoxy resin glue according to the color and reflective properties of the original stone
Or unsaturated resin
glue, and then repair it after toning, use a weighting machine, a refurbished disc and,,,,,,,3 polishing discs, diamond water grinding discs
to polish one by one . The polishing method and precautions are the same as those for light renovation. For example, if Yirui Company's Yimei marble crystal hard powder is used for stone crystal hardening treatment, during the renovation process, after grinding with diamond water grinding discs, marble crystal hard powder can be used directly for treatment. Crystal hardening treatment makes the surface of the stone as bright as new.
Renovation of old marble
Thoroughly clean the floor with a dry and clean floor mop. There will be no sand or impurities on the floor
After the overall cleaning of the stone surface is completed, use marble glue to Repair small damaged spots on each stone and seams in the middle of the stone. First, repair the original damaged surface with marble glue close to the color of the stone. Then use a special stone cutting machine to neatly cut and slit the middle seam of the original stone installation to make the width of the gap consistent, and then fill it with marble glue close to the color of the stone (Note: If the middle seam has been processed before, No need to re-sew). After repairing with marble glue, you must wait for the glue to dry completely before proceeding to the next step.
After the marble glue is dry, use a grinder to polish the entire floor. Grind the entire floor horizontally, focusing on the caulking glue between the stones
(the diagonal corners between the stones) and near the wall. At the edges of edges, decorative shapes, and special-shaped shapes, keep the overall stone floor flat, complete the first pass of polishing, and re-carry out the marble glue caulking
. After the caulking
is completed, proceed to the second step. Second polishing, and then use a stone refurbishing machine
with steel diamond water grinding discs from coarse to fine (mesh, 3 mesh, mesh, mesh, mesh, mesh, mesh). A total of seven times of grinding are required to polish the final floor. The whole surface is flat and smooth, and then polished with steel wool
. The polishing degree reaches the brightness (degree) required by the design, and there are no obvious gaps between the stones
. After polishing, use a water absorber to clean the ground
Treat the moisture, and use a blow dryer to dry the overall stone floor. If time permits, you can also use natural air drying to keep the stone surface dry
. Spray 3 liquids evenly on the ground while using marble. Polishing machine
Grinding, use a cleaning machine
with a red scouring pad
, sprinkle 3 potions and an equal amount of water on the ground, use a rpm floor scrubber to start grinding with load, heat energy The surface effect formed by the crystallization of the crystal surface material on the stone surface
. Overall ground maintenance treatment: If it is a stone with large voids (sandstone
, travertine
, etc.), it is necessary to Apply the marble protective agent
, and after an hour, use a floor scrubber
to alternately finish and polish the floor with 3 liquids, that is, five times in total, and then replace with a white polishing pad
, spray a small amount of potion, and polish it again to increase the crystal surface hardness of the entire floor
. Floor cleaning and maintenance: When the surface of the stone forms a crystal mirror, use a vacuum cleaner to suck off the crystal surface on the ground
Residues and moisture are removed, and finally polished with a polishing pad to make the entire floor completely dry and as bright as a mirror. If it is partially damaged, local maintenance can be performed. After the construction is completed, you can walk on it at any time.
Polishing machine
Operating procedures and precautions
Polishing machine
The operating procedures are as follows:
． Ground garbage, debris, sand, etc. need to be removed before polishing.
． Check whether the polishing brush of the polishing machine is clean and whether to replace it.
． Check whether the adjustment key controller is in the normal machine speed position.
． Connect the power supply, and the operation should start from the place closest to the power supply. After turning on the machine and letting the machine run at high speed, then stick it to the ground for polishing. The walking route should be a straight line, and the polishing position at the back should overlap the polished ground at the front.
Pay attention to the following points when using the polishing machine:
Do not lift the operating lever during operation, as this may cause the machine to lose control.
You cannot press anything on the machine because it has a precise balance range. When the operating rod needs to be moved, all wires must be moved first.
The ground wire must be connected to the switch box motor. Wrong connection will lead to electric shock and danger.
Do not operate the machine in a flammable and explosive atmosphere.
. Don't drive the machine too fast to avoid collision.