The best selling mortar spraying machine mortar spraying machine

Shandong Zhongyan Mining Equipment Manufacturing Co., Ltd. Contact: Li Xiao Mobile:
Landline: Fax:
Email: @
Address: No. Jinyu Road, Rencheng District, Jining City, Shandong Province
Company Website:
Introduction to a mortar spraying machine
The mortar spraying machine is simple to operate and does not require scaffolding, moving equipment, or repairs. Both the yin and yang corner roofs can be sprayed freely, shortening the construction period and improving efficiency. progress, and save the expenditure on frame materials.
The mortar spraying machine is a professional spraying machine specially used to spray mortar. It can be used to spray mortar with mortar particles below four or five millimeters.

The mortar spraying machine can not only be used for spraying, but also for pouring mortar. In addition, the mortar spraying machine is known as the fast mortar spraying machine because of its high efficiency spraying speed. Because it can spray cement, it is also called fast cement mortar spraying. machine. Because it can spray putty powder, refractory materials, latex paint, and fireproof materials, it is also known as a multi-functional sprayer.
Product features of the second mortar spraying machine
Suitable for spraying materials: putty powder coating, latex paint, real stone paint, cement mortar, dry powder mortar, insulation mortar, waterproof material, fireproof material, heat insulation material, sound-absorbing material and other water-soluble materials.
Adjust the flow rate to achieve the best spraying effect.
In addition to the switch on the electric control box, it is also equipped with a remote control switch for spraying.
The connection between the spray gun and the feeding pipe can be rotated for easy operation.
High construction efficiency and good quality.
It is small in size and easy to carry on site, and the cost of accessories is low and maintenance is simple.
Easy to use, fast, saves materials, labor, and money. One machine only requires three people, square meters/hour (thickness).
Material proportion (cement): mortar.
Advantages of three-mortar spraying machine and traditional manual investment income
Compared with traditional manual wall plastering and the performance of previous wall painting machines launched on the market, using a fast putty mortar spraying machine has the following advantages:< br/> There is basically no dust on the floor, saving water and materials, which can reduce costs by more than %.
Fast speed, high efficiency and low labor intensity. One (multi-function speed-adjustable) spraying machine can easily spray ㎡ per hour. Excluding preparation time, calculated in working hours per day, it can spray more than ㎡, which is equivalent to the hard work of a skilled worker. A day's work.
The investment is small and the profit is large. If each (multi-function speed-adjustable) spraying equipment sprays m2 per day, calculated based on the average market price of RMB per m2, excluding the workers’ wages of approximately RMB RMB, each equipment can make a profit of RMB RMB per day, excluding Other factors, an annual income of more than 10,000 yuan, are also expected.
Operation Guide for the Four Mortar Spraying Machine
Before starting each shift, press the hand oil pump several times to inject oil into the transmission part.
After turning on the power, first motor the main motor and check whether the rubber spiral rotation direction is consistent. If not, replace the power phase wire (this check must be performed every time the power is reconnected)
Connect the conveying hose and nozzle, add clean water to the hopper, start the motor to pump out the clean water to wet the hopper, pump body and conveying hose. Stop the machine after most of the water is pumped out.
Add putty or paint into the hopper to start spraying (you should start the air compressor first and open the air valve)
It is strictly forbidden to idle without material and water in the hopper.
After the work is completed, the remaining materials in the hopper must be drained, and enough clean water should be poured into the hopper. Clean the hopper, start the pump, and clean the hose and nozzle until all the water comes out of the pump to prevent the remaining materials from being stored in the soft The pipe solidified, blocking the hose and nozzle.
If the machine has been shut down for too long, wipe the machine clean and remove the booster screw. After applying oil, keep it properly and reinstall it when using it.
If the pump pressure is insufficient during work, you can adjust the booster stator bolts or replace the booster rubber sleeve and booster worm.

Before spraying, the sprayed area should be sprayed evenly in layers with the nozzle as perpendicular to the sprayed surface as possible (the distance can be adjusted according to the spraying effect), and coordinated with the flattening process. If the wall is too dry or the time after spraying is too long will seriously affect the flattening effect, the process must be changed.
Fill the hopper evenly without interruption. When the conveying spiral rotates, it is strictly forbidden to use sticks to stir in the hopper to prevent injury to people.
Once the shotcrete delivery pipe is blocked, switch the switch to the manual position, turn on the compressor only, remove the quick connector in front of the pump head, and then block the nozzle head downwards. The wind pressure will generate reverse pressure and move the delivery pipe Blow out the remaining slurry, install the quick connector, and start working normally.
When spraying hands, you should wear protective equipment such as safety helmets, protective glasses, and protective clothing.

The supercharger rubber sleeve and supercharger screw are wearing parts. In order to extend the service life, the supercharger stator bolts are in a loose state when used for the first time. They will be adjusted when the pressure is reduced and the flow rate is significantly reduced. Tighten the bolts so that they are in normal working condition.