Multi-head electric capping machine capping machine wholesale

Stainless Steel Electric Capping Machine_Capping Machine_Multi-head Electric Capping Machine Product Introduction:
The capping machine is a desktop three-knife cyclone capping machine. This machine has a stainless steel appearance and is safe and convenient to operate. When working, the capping machine is capped The bottle does not rotate, and three cyclone knives are evenly distributed to rotate and cap the seal. The knife handle is designed with a spring structure. The distance between the three knives can be fine-tuned. It has strong adaptability and high capping yield. This machine is suitable for military units, hospitals, laboratories, small Ideal for pharmaceutical plants.
Main technical parameters:
, usage specifications - ml glass bottle sealing
, production capacity - bottles/minute
motor power,
, appearance dimensions:
, Machine weight:
Detailed introduction:
1. Adjustment of the upper arm when rolling bottles of different specifications:
This machine can be used to roll - bottle caps, when using bottles of any specification , just put the bottle of this specification on the pallet, hold the cross arm with one hand, and loosen the nut on the left side of the cross arm with the other hand, so that the cross arm drops or rises until the capping head is about 1 mm from the bottle cap. Tighten it, and then use the included hexagonal wrench to close the support ring against the cross arm and lock the support ring. (Note) When tightening, pay attention to the alignment of the capping head and the bottle cap.
2. Adjustment of the mold support block. Place the bottle into the lower mold support block, loosen the two screws on the support block, and move the bottle and the lower mold block together until the capping head and the bottle cap are aligned. Finally, tighten the two screws on the mold block.
3. Specific operation method: Put the bottle filled with liquid and capped on the lower tray, lean on the support block, hold the bottle with one hand, and pull the handle backward and downward with the other hand. At this time, the tray holds the bottle and is lifted upward until the bottle cap and the capping head are pressed tightly.
After the bottle cap and the capping head are pressed tightly, the three capping cutter heads that keep rotating rotate several times to tighten the bottle cap. (Note) The motor must run clockwise.
Push the handle forward so that the rolled cap returns to its original position along with the tray. The entire operation process is completed. Repeat the above operation every time you roll a bottle cap.
4. Adjustment of the capping head:
The machine is equipped with multiple capping heads, and the capping head can be selected according to the size of different bottle caps. You can try it with a bottle before formal use.
If the cap is not rolled tightly, you can unscrew the locking nut of the capping head and unscrew the upper capping head counterclockwise, and then lock the upper fixing nut.
, The cap is rolled too tightly, and there is a phenomenon of rotary cutting of the bottle cap. You can unscrew the locking nut of the upper capping head and screw in the upper capping head clockwise, and then lock the upper fixing nut.
If the lower edge of the bottle cap is not tightened tightly, the eccentricity of the three rolling cutter heads can be appropriately adjusted according to the actual situation. If the tightening is too tight and the bottle may be crushed, the eccentricity of the three rolling heads can be appropriately increased.
5. Reference values for adjustment of some bottle caps
Bottle cap type - :r
Distance from the lower plane of the locking nut to the flat surface of the capping head - :r
The lower plane of the capping head to the pallet Upper plane distance
Oral liquid - :r
Self-adjusted according to the position of the upper adjustment wheel - :r
Self-adjusted according to the height of the bottle
Vial - :r
- :r
Large infusion - :r
- :r
Our company sells various specifications of glass bottles, small cillin bottles, penicillin bottles, large infusion bottles, controlled bottles, molded bottles and Various rubber stoppers and aluminum caps, low price and high quality. For more detailed information on filling machines, capping machines, sealing machines, capping machines, capping machines, capping machines, packaging machines, and locking machines, please visit our company's website
: Consultation phone number:
Keywords in this article: Electric capping machine, multifunctional capping machine, electric multifunctional capping machine, glass bottle electric capping machine