Year1
- 外廓尺寸：
- 1500 mm×630mm×760mm
※Product introduction:
Power type: machine
Maximum grinding head speed:
Grinding wheel specifications:
Grinding wheel stroke:
Grinding wheel inclination angle: -
Feed amount per revolution of the handwheel:
Dimensions:
Quality of the whole machine:
Working principle: .type internal combustion rail grinding machine, powered by the machine, drives the synchronous belt through the centrifugal clutch The power is transmitted to the spindle through the synchronous belt to drive the grinding wheel to rotate. At the same time, a feed hand wheel is used to adjust the feed amount of the grinding wheel. If you need to grind the rail side and arc, you can rotate the profiling hand wheel to The rails are ground for rail shape.
Precautions for type II internal combustion profiling rail grinder
Before use, engine oil must be added according to the machine instructions
Do not use a grinding wheel with a speed lower than r/
Replacement The grinding wheel must be stopped before use
. Never use a damaged grinding wheel
. After replacing the grinding wheel, run it idling for 3 seconds. During the test run, other personnel must stay away from the site
. Check whether the grinding wheel is intact before use. , check whether the fastening nut is loose.
The angular contact bearings of the grinder spindle, the rolling bearings of the guide wheels, the running wheel bearings, the intermediate wheel synchronous pulley bearings, the clutch bearings and other bearings must be regularly injected and replaced with grease.
After the machine has been running for a cumulative number of hours, the main shaft bearing should be disassembled and cleaned, and the grease should be replaced.
Do not throw or drop during use and transportation.
If not used for a long time, the machine should be placed in a ventilated, dry and corrosive-gas-free warehouse, and the internal combustion engine should be drained of fuel.
The grinding wheel should be moisture-proof, anti-collision and anti-pressure.
The recommended operating environment temperature of the machine is between -℃~℃.
It is recommended to use lead-free products with an octane number or higher. When refueling, the engine should be stopped and kept away from fire sources. Refueling should be done in an appropriate amount. After refueling, the surface of the machine should be wiped clean of residues.
Frequently check whether the lubricating oil of the machine is sufficient and whether the air filter is clean.
. Do not let the machine and tools get exposed to rain. If they are exposed to rain, dry the machine and all parts of the machine.
Safety measures and methods of use
(1) Safety measures before use:
Check whether the fuel and oil levels of the machine are sufficient. If they are insufficient, add fuel and oil first. Please refer to the machine manual for specific methods.
Before operation, first rotate the feed handwheel to the top to keep the grinding wheel away from the rail surface, then support the auxiliary support frame, start the machine, and idle for 3 seconds to check whether the transmission part is flexible and whether there are any abnormalities. Noise, whether the threaded connection is loose.
The rail grinding machine is operated by one or two people, with one hand holding the profiling handwheel and the other holding the profiling frame.
When grinding, the operator must wear appropriate protective equipment: glasses, gloves, etc.
If polishing sparks fall on or are close to flammable materials, protective measures should be taken to avoid fire.
(2) Operation method:
According to the above prepared work, when turning the feed handwheel 3 clockwise, the grinding wheel will move down.
To obtain good polishing quality, two steps must be followed.
) Rough grinding: Grinding should start from the rail surface. The grinder moves back and forth along the rail, slowly lowers the grinding wheel and grinds the raised parts. After grinding to the rail surface, rotate the profiling handwheel to grind the side according to the above method.
b) Fine grinding: Based on the rough grinding, the grinder is repositioned to prepare for grinding the rail surface. When the grinder is in place, lower the grinding wheel so that it just touches the rail surface that does not need to be polished near the weld. Start grinding from the rail surface, and then rotate the profiling handwheel to grind the sides. The grinding range should reach both sides of the weld. To compensate for grinding wheel wear, the grinding wheel feed should be adjusted at any time.
After the grinding is completed, the handwheel must be rotated counterclockwise to lift the grinding wheel to facilitate grinding of the next weld, reduce the throttle, turn off the switch, turn off the machine, and stop the operation.
Before going down the road, reset the copy frame and the frame vertically to ensure transportation safety.
Troubleshooting
Fault phenomenon
Cause
Troubleshooting method
Spindle does not rotate
Grinding wheel tops rail before machine starts
Grinding wheel feed amount is too high Large
Lift the grinding wheel
Lift the grinding wheel
The track fell off when grinding the rail side
The gap of the running wheel on the side to be grinded is not eliminated
Before grinding, eliminate the gap first
The feed handwheel rotates
The spindle feed locking steel ball spring is aging
Replace the spindle feed spring
The machine does not start
Follow the machine instructions to troubleshoot
※Company introduction:
Jining Hengwang Industrial and Mining Machinery Co., Ltd. is located in the charming city of Jining, the hometown of Confucius and Mencius and the capital of canals. It borders the Oriental Holy City Qufu to the east, the historic Beijing-Hangzhou Grand Canal to the west, and the historic Beijing-Hangzhou Grand Canal to the south. It is adjacent to Qilu Lingxiu Weishan Lake and to the north is Mount Tai, the most famous of the five mountains. The company was established in 2001 with a registered capital of RMB 10,000 and currently has more than 100 employees. It specializes in operating rock drills, rock drills, shotcrete machines, support equipment, scraper accessories, rail equipment and other mining equipment and accessories according to market needs. The company adheres to the business philosophy of providing convenient services to customers, creating development opportunities for employees, and the entrepreneurial spirit of being enterprising and enjoying success. We warmly welcome new and old friends from all walks of life at home and abroad to negotiate trade, create great causes and create brilliance together.
※Contact information:
Mobile:
Telephone:
Fax:
Manager: Zhang Shuang WeChat:
:
Email: @
Website::3
※After-sales service and delivery instructions
, Cost-effectiveness instructions:
Under the same product quality conditions, our company will not provide any information at the expense of reducing performance or changing product parts. The lowest and most realistic price. (Product production configuration can be carried out according to customer requirements)
Delivery instructions:
Delivery is based on the supply period. If there are special circumstances that require early delivery, our company will do so within a limited scope. We will organize personnel to increase productivity, implement production, installation, debugging, packaging and other processes, and strive to meet your company's requirements
Product delivery comes with instructions:
①Product manual and maintenance manual
②Product Certificate of conformity
③Instructions attached to purchased parts
④Wearing parts and their list (the source may vary depending on the model)
. After-sales service scope:
The product warranty period is one year. If the product has quality problems during the warranty period, our company will provide the fastest maintenance without any cost. If parts need to be replaced outside the warranty period, our company will only charge the cost
Track the product:
Our company will After the product is sold, there will be at least one technical return visit every month to track and record the use of the product so that any problems can be dealt with in a timely manner and strive to achieve customer satisfaction.
WhatsApp
