T8led infrared sensor lamp, human body infrared sensor lamp

Infrared sensor lamp, human body infrared sensor fluorescent lamp, human body infrared sensor lamp, infrared human body sensor lamp
Must be lighting infrared human body sensor

The main features of fluorescent lamp:
,
Double brightness,
meet the monitoring needs of underground garages when dimly lit,
brighter than ordinary fluorescent lamps at full brightness
, and have a comprehensive energy saving rate compared with ordinary fluorescent lamps when used in underground garages
Power saving
above
, super long life:
(
) Exclusive use of
hours electrolytic capacitor,

Long driving life
(
) Using the industry’s thickest aluminum kit for heat dissipation and high thermal conductivity
aluminum substrate, the lamp beads have low operating temperature, small light attenuation and long life
(
)
year warranty
, compared with ordinary

fluorescent lamps in the lighting market:
The brightness is the average
< in the lighting market br/>Fluorescent lamp
Twice as bright
Factory direct sales, affordable price,
Fluorescent lamp is lower than the price in the lighting market
Please call
:
for details Inquire and request samples!
Benefits you will get
Brightness improvement
+
Power saving
(satisfied at the same time)
Must be lighting infrared induction fluorescent lamp finished product light efficiency up to /, Replacing the original fluorescent lamp (the actual power is usually -) saves electricity while increasing the brightness. The electricity bill saved in the underground garage in about 3 months is enough to buy lamps, and the annual return on investment
3
.
At least more than 100 yuan of electricity will be saved during the entire lamp life cycle. The boss is concerned that the return on investment is as high as 3, 3 times or more! Call now:
Start saving energy in three days!
Modify a lamp in three minutes, the modification is extremely simple
You can modify a set of lamps in about 3 minutes, remove the lamp tube and starter from the original fluorescent lamp, and connect the two wires of the ballast Short-circuit it and replace it with a fluorescent lamp. Usually the electricity bill saved in about 3-months can buy this batch of lights. Call now:
Start saving energy in three days!
It must be the exclusive advantage of lighting and additional benefits for customers
, exclusive use of

large chip lamp beads, the luminous flux of a single lamp is
above,
in the industry The highest finished product brightness can meet the original illumination requirements without
,
improving owner satisfaction
, a new level of power saving in the industry, above average

, large chip Lamp bead
+
Thick high thermal conductivity aluminum substrate
+
Thick aluminum kit,

The lamp bead is at a very comfortable low temperature (
degrees Within) working
,
The ultra-thick kit, coupled with the five-layer super-hard corrugated outer packaging, can hardly be damaged even by the most violent logistics
, Sino-Japanese joint venture high-performance sensor
+
German special digital processing chip brings the highest sensitivity and high reliability in the industry
Exclusive use
High temperature resistant and long life electrolytic capacitor, the life is three times that of ordinary manufacturers The above
, high reliability, long life,
year warranty, solve all the troubles of lighting maintenance once and for all, and the master electrician has nothing to do all day long, month after month.
The perfect production process of Biwei Lighting ensures the top quality in the industry
. We use the industry's most advanced fully automatic soldering iron and the industry's top

Yatong
3
The proportion of no-clean solder wire increases the welding efficiency
while every solder joint is as bright as new
We use the most advanced four-wire stripping and twisting machine in the industry, which is highly efficient. More than doubled, and at the same time, we use the national standard multi-stranded pure copper wire of the old brand to prevent the solder joints from falling off due to hard wires during transportation, prevent oxidation, and extend the service life of the product
We use the most advanced fully automatic screw machine in the industry , set at the optimal
disengagement torque to ensure that every screw is tightened just right, and at the same time, it is more than three times more efficient than ordinary manual screw tightening
Call now: - Start saving electricity in three days!
Application occasions
Infrared sensor lamps, human body infrared sensor fluorescent lamps, human body infrared sensor lamps, infrared human body sensor lamps are widely used in various occasions such as underground garages, parking lots, corridors and aisles, etc. Renovate or replace the original fluorescent lamp.
Must be lighting

Infrared sensor lamp, human body infrared sensor

Fluorescent lamp, human body infrared sensor lamp,
Infrared human body sensor lamp< br/>Specification model:
<> Specification model
<> Total power
<> Number of lamp beads
<> Corresponding (nominal) power
<> Section Electricity
<> Overall dimensions (long diameter)
<>
<>
<>
<>
<>
<>
<>
<>
<>
<>
<>
<>
<>
<>
<>
<>
<>
<>

Note: The length of the original lamp tube and the size of the lamp holder are exactly the same.
Infrared induction

The main differences between fluorescent lamps, voice-activated fluorescent lamps and radar-induced fluorescent lamps
Among the lighting fixtures in underground garages, infrared-induced fluorescent lamps, radar-induced fluorescent lamps and voice-activated induction fluorescent lamps are the mainstream What are the advantages and disadvantages of each of the three lighting fixtures used?
Infrared induction fluorescent lamps mainly rely on infrared pyroelectric sensors to detect the movement of heat sources. They have high sensitivity, few malfunctions, stable performance, and long life. They have great performance advantages in underground garage applications, and their production costs are lower than radar and voice control. The price is about 3 yuan. Detailed inquiry:
How to judge
Infrared sensor lamp, human body infrared sensor

Fluorescent lamp, human body infrared sensor lamp,
Infrared human body sensor lamp
Is it good or bad?
When buying fluorescent lamps, you usually need to pay attention to brightness, heat dissipation and lifespan: how bright the lamp beads are used (determines whether it is truly energy-saving and high-brightness), whether it is made of aluminum substrate (thick..., thin...) or glass. Fiber board (determines how many years the brightness can be maintained), whether it is a constant current driver (to prevent lamp beads from burning), the life of the driver (mainly determined by the life of the electrolytic capacitor), and whether there is an aluminum kit for good heat dissipation.
Must be lighting
Infrared sensor lamp, human body infrared sensor

Fluorescent lamp, human body infrared sensor lamp,
Infrared human body sensor lamp
Configuration
It must be a lighting fluorescent lamp, using the industry's top 3/pcs/. lamp beads (gold wire, copper bracket), the finished product has a light efficiency of more than . For power saving and above, the industry's top-notch half-aluminum and half-plastic kit is used. The thickness of the high-thermal conductive aluminum substrate ensures good heat dissipation and reduces light attenuation. The constant-current drive efficiency is up to . Brand R has the longest life of electrolytic capacitors in hours.
Must be lighting

Infrared sensor lamp, human body infrared sensor

Fluorescent lamp, human body infrared sensor lamp,
Infrared human body sensor lamp< br/> Adopt the best configuration on the market, with the highest brightness and light efficiency, the longest life,
year warranty, factory price direct sales, affordable price, fast delivery! Please call
:
for details and to apply for free samples!
If you buy such

infrared sensor lamp, human body infrared sensor

fluorescent lamp, human body infrared sensor lamp,
infrared human body sensor lamp Guan
Customers will only have short-term joy?
If you use Zhongshan cents lamp beads, fiberglass boards, non-constant current drives, the most rubbish electrolytic capacitors, .3 heat sinks, or all plastic or glass, you will not be satisfied at the beginning, and even more Many worries will arise in a few months. These configurations cannot satisfy our requirements for
infrared induction lamps, human body infrared induction

fluorescent lamps, human body infrared induction lamps,
infrared human body Induction lamp
Good expectations for brightness and lifespan!