Kalian ZJ-2001A alcohol detector

卡利安ZJ-2001A酒精检测仪：

卡利安ZJ-2001A酒精检测仪

卡利安ZJ-2001A酒精检测仪：

卡利安ZJ-2001A酒精检测仪

卡利安ZJ-2001A酒精检测仪：

卡利安ZJ-2001A酒精检测仪

Introduction: . This product is equipped with a high-precision semiconductor alcohol sensor-ceramic sensor (patent number: Korean Patent Office,). Such as smoking, drinking, etc. this instrument will not reflect. The semiconductor sensor in the instrument reacts with alcohol molecules to resist changes in measurement and analysis, so it is very accurate and the maximum error rate is lower than ./.
.
The error rate of this product is very small, and the stability and accuracy of high-concentration measurements are fully demonstrated in comparative experiments.
3.
This product adopts a special structure (sensor protector) to avoid contamination of the instrument by saliva, sand and dust, etc., and to protect the sensor.
.
This product adopts a super lightweight design and its appearance conforms to ergonomic principles, which can avoid work fatigue caused by long-term use and carrying.
.
This product is simple to operate and comes with a genuine leather jacket, making it easy to carry and use at work.
.
This product is equipped with dual call-in devices (disposable, multi-purpose), suitable for different working environments.
.
The biggest feature of this product (the fundamental difference from other products) is). It does not react to non-alcoholic gases. b). It can accurately detect high or low concentration alcohol. ). The mouthpiece adopts a non-contact multi-purpose mouthpiece, so there is no need to replace the mouthpiece for testing. .
How to use
Press the switch (R), the display will show, and it will change after a few seconds.
When it is displayed and makes a beeping sound, and the standby light is on, the detection can be started.
Ask the person being tested to aim at the air inlet of the instrument and blow continuously for 3 seconds. At this time, two beeps will be emitted. After the two beeps, the standby light and the no-pass light will flash at the same time, and the data will be displayed at the same time.
.
Press the reset (R) button at this time to put the instrument into standby mode and prepare for the next operation.
If the battery indicator light (B) shows a yellow light, you must replace the battery in time or connect the car power cord to the round hole on the right, then you can use it
Special note: Do not block the exhaust port during measurement
Normal operating temperature: minus degrees Celsius to above zero degrees Celsius.
.
If alcohol enters the instrument by mistake (including alcohol content in the mouth), the display will show overheating protection, which means there is alcohol remaining in the instrument. You need to wait - minutes for the alcohol in the instrument to After it is fully evaporated, wait for use again.
Precautions during use
Read the instruction manual carefully before use.
The optimal time is measured from 3 minutes after drinking.
If the power indicator light is on, replace the battery in time and use alkaline batteries.
Do not disassemble the instrument casually.
The contact port must be kept clean to prevent dirt from entering and damaging the instrument.
It is prohibited to block the air outlet with your hands during inspection.
Product Spec Sheet
Specifications

Weight
g
Casing
Shockproof, cast hard plastic
Sensor
Highly selective semiconductor oxidation sensor
Response time
seconds
Warm-up time
seconds
Battery
Alkaline battery additional reserve power supply car power supply
Test Scope

～
Warranty
Year
Non-printable alcohol detector Printable alcohol detector Alcohol detector Cheetah alcohol detector Kalyan-alcohol detector Tianying No. 1 Alcohol Detector King Kong No. 3 Alcohol Detector Alcohol Detector Alcohol Detector Model Alcohol Detector Wholesale Alcohol Detector Price Traffic Police Special Alcohol Detector Alcohol Content Detector
Beijing Detaiyuan Safety Prevention Technology Co., Ltd.< br/>Wang Youcai
Address
No. South Third Ring West Road, Fengtai District, Beijing
-Alcohol Test_ />