CW6180 Universal Lathe Manufacturer 80 Lathe Market Hot Selling

The complete motion process of the universal lathe manufacturer's lathe is:
The cutterhead of the universal lathe manufacturer's lathe is released. The cutterhead is clamped by turning left or right to the nearest designated tool position. Then the corresponding action sequence of the electromagnet is: power on (the cutterhead is released) (forward rotation) or (reverse rotation) power on (the cutterhead rotates) (for forward rotation) or (when reverse rotation) power off (the cutterhead stops rotating) Power off (cutterhead clamped). The working principle of the jet tube hydraulic servo system is composed of a hydraulic cylinder, a receiving plate and a jet tube.
The jet tube of the general lathe manufacturer's lathe can swing to the left and right at a small angle around the axis perpendicular to the drawing surface. There are two side-by-side receiving holes on the receiving plate, and the pressure oil injected from the tapered nozzle at the end of the jet pipe is directed to the left and right chambers of the hydraulic cylinder respectively, causing it to move to the left or right. When the jet tube is in the middle symmetrical position of the two receiving holes, the pressure of the oil in the two receiving holes is equal. The hydraulic cylinder does not move. If an input signal acts on the jet tube to deflect it, for example, it deflects to the left at a small angle. The pressures in the two receiving holes are not equal. At this time, the pressure in the left chamber of the hydraulic cylinder will be greater than that in the right chamber. The hydraulic cylinder will move in the direction of deflection of the jet tube (to the left in this case) until the receiving plate that moves with the hydraulic cylinder arrives. until the jet hole is at a symmetrical position in the middle of the two holes.
<= d%> %> Specifications and models
%> >
%> Lathe lathe
%> Maximum rotation diameter of the lathe bed of a general lathe manufacturer
%> >
%> >
%> Maximum rotation diameter on tool holder
%> >
%> >
%> Maximum workpiece length
%> >
%> >
%> Rotation diameter/effective width in saddle groove
%> >
%> >/
%> Spindle through hole diameter and shaft head type
%> >
%> >(Series) (Series)
%> Spindle through hole front end taper and top taper
%> >
%> >( Series) (Series) Mohs No.
%> Universal lathe manufacturer lathe spindle speed series and range
%> >r /
%> >Type-(Series)
Kind.-(Series)
%> Longitudinal feed level and range
%> >/
%> > Kind
%> Range:
%> >/
%> >
%> Range:
%> >/
%> >
%> Micro feed range using exchange gear
% > >/
%> >
%> The ratio of transverse feed amount to longitudinal feed amount
%> >
%> >/
%> Saddle Rapid traverse speed
%> >/
%> >
%> Machine tool screw pitch
%> >
%> >(metric)/(imperial)< br/> %> Number and range of metric thread types
%> >
%> >Type- (there are also non-standard threads)
%> Number and range of inch thread types
%> >
%> >Species- .
%> Number and range of module thread types
%> >
%> >Species
%> Diameter joint Number and range of thread types
%> >
%> >Type-D
%> Maximum lateral travel of lower tool rest
%> >
%> >
%> Maximum stroke of upper tool rest
%> >
%> >
%> Tailstock sleeve stroke
%> >
%> >
%> Tailstock sleeve taper
%> >
%> >Mohs number
%> Lathe bed guide rail width and quenching hardness
%> >
%> >
%> Main motor power
%> >
%> >
%> Fast motor power
%> >
%> >< br/> %> Cooling pump motor power
%> >
%> >
%> Machine tool width and height
/Packaging width and height
%> >
%> >
/ /
%> Machine length/packing box length
%> >
%> >
%> Maximum workpiece length
% > >
%> >
%>
%> >
%> >
%>
%> >
%> >/
%>
%> >
%> >
%>
%> >
%> >/
%>
%> >
%> >/
%>
%> >
%> >/
%> Net weight of machine tool
%> >
%> >
%> Maximum workpiece length
%> >
%> >
%>
%> >
%> >
%>
%> >
%> >/
%>
%> >
%> >
%>
% > >
%> >/
%>
%> >
%> >/
%>
%> >
%> >/
%> Bed width
%> >
%> >
%> Maximum load-bearing
%> >
%> >