Year1
- 电压：
- 380v
- 功率：
- 19kw
- 占地：
- 直径11米
The amusement machine is driven by an electric motor that is decelerated by a reducer, and the driving power passes through the central slewing bearing for rotational motion. The other power passes through the eccentric structure to realize the up and down lifting motion of the cabin. The equipment can be stopped within a specified time after operation.
Two technical parameters:
Product name
Big Octopus Speeder
Voltage
Power
Crew
- People
Area
/> Diameter (including column area - meters)
Place of origin
Zhengzhou, Henan
Three installation and commissioning:
Before installing the amusement machine, check whether the components and accessories are complete according to the packing list. .
. The amusement machine must be installed on a flat base on hard geological ground and fixed on a concrete foundation. The fence is fixed with expansion screws.
, Connect all parts of the amusement machine.
Check whether the connecting bolts of each component of the host are firm.
Install the cockpit according to the forward direction of the cockpit (clockwise) and fix the connecting holes at the bottom of the cockpit and the connecting holes on the bracket with bolts.
. Connect the output end of the collector carbon brush on the main unit to the power supply and the corresponding wire number of the terminal block of the control cabinet.
Four operations:
Close the power switch of the electrical control cabinet and turn the key switch clockwise to the on position.
. When the start button is pressed, the speaker of the electric control cabinet emits a beep sound. About a second later, the electrical control system turns on the power to the motor. The cabin rotates and lifts under the action of the transmission system. At the same time, the speaker moves along with the cabin. Plays analog electronic sounds.
When the set time is reached, the speaker will emit a shutdown prompt for seconds and the entire operation process will end.
When it is necessary to stop, press the emergency stop button and the equipment will stop running.
When suspending use of the amusement machine, turn off the power switch of the control cabinet or cut off the power supply.
Five: Safety precautions:
The power supply provided by the user to the amusement machine should be protected by a leakage switch, and the ground electrode in the power socket must be reliably connected to the protective ground wire (net). The connection of each group of electrical conductors must be Operated by professional electrical installers.
The metal shell frame of the electric control cabinet must be reliably connected to the protective grounding wire. (Ground resistance)
Children can enter or leave the cabin only after the amusement machine has stopped safely. Only two passengers are allowed in each cabin.
Children in the cockpit are not allowed to start the amusement machine unless they are seated and stabilized.
When the amusement machine is in operation, no one is allowed to enter the fence and passengers are strictly prohibited from leaving the cabin.
If the amusement machine is not running normally or cannot stop automatically, turn off the main power switch immediately.
During the maintenance of the amusement machine, the power supply must be cut off in advance.
When replacing the fuse, you must use a fuse that is consistent with the original specification.
Six: Maintenance and repair:
The inside and outside of the amusement machine should always be kept clean.
Before using the amusement machine, check the condition of all parts of the machine. The fasteners should be carefully checked and tightened. After tightening, check and tighten regularly or irregularly.
Check the reducer oil regularly or irregularly (the oil level should be higher than the worm tooth surface).
Depending on the usage, add grease to the gear bearings regularly or irregularly.
After using the new amusement machine for a period of time, you should check and adjust the position of the motor pulley to tighten the belt appropriately.
If the amusement machine is not put into use for a long time, it should be started for at least one hour every month to keep the mechanical and electrical system of the amusement machine in good working condition.
. The electrical control cabinet must be protected from rain, moisture and immersion.
Seven faults and maintenance:
Fault phenomenon
Failure analysis
Maintenance and troubleshooting methods:
The motor cannot start
The centrifugal switch of the motor cannot be closed or the position is deviated Failure to move it clean will result in poor contact.
Check the centrifugal switch adjustment position and clean the contacts.
The coil tie wire between the motor pole and the rotor is fused.
Treat the fracture well.
There is dirt in the oil loss of each bearing transmission part, the bearing is damaged, etc., resulting in poor rotation.
Clean and refuel bearing rotating parts and even replace bearings.
Capacitor breakdown
Replace capacitor
Center bevel gear clearance is too small
Adjust bevel gear clearance
Belt slipping
V-belt is loose or failed
Adjust the position of the pulley so that the belt is properly tightened and replace the failed belt.
The reducer leaks oil along the shaft end
The oil seal is damaged
Replace the skeleton oil seal
The amusement machine does not start after pressing the start button
The power supply is out of power and the fuse is blown
Check the power supply and replace the fuse
The amusement machine cannot operate normally after starting
Overcurrent causes the switch to automatically cut off the power supply
Check the motor and overcurrent switch.
The conductive carbon brush has poor contact with the conductive copper ring or the carbon brush is severely worn.
Clean the conductive device and replace the carbon brush.
The amusement machine cannot automatically stop running within the timing control time
The connector is loose
Check each connector point.
The timing value switch has poor contact or the timing circuit board is faulty.
Repair or replace
WhatsApp
