PIE 830 multifunctional calibrator

Detailed introduction
The multifunctional process calibrator can calibrate various thermocouples, thermal resistors, voltages, millivolts, frequency pressures, accepts a wide range of digital pressure modules, and has loop diagnosis and patented leakage test functions. . A free traceable calibration certificate is included as standard. Spot goods.
Product Features
Eliminate hidden loop problems
Unique patented loop diagnosis technology quickly diagnoses faults such as ground faults, leakage, etc. This is a function that other instruments do not have.
Check all parameters of the circuit at one time
At the same time, the voltage, current, and resistance are displayed, allowing the user to understand the real-time status of the circuit. Identifies overload problems in power supplies and circuits. These are patented technologies
, automatic detection line thermal resistance
patented technology to solve the problem of transmitting sensor connection and find out the damaged lines. The LCD displays each line connected to the sensor.
Replace a failed transmitter to diagnose control problems
Easily functions as a general purpose temperature, frequency, mA, or pressure transmitter. If a transmitter fault is found in the loop, you can turn on loop detection to check the loop current, supply voltage, and load to troubleshoot.
, Substitute multimeter to solve line faults
When checking the continuity of the circuit, there is a buzzer prompt, which can quickly find the broken or short-circuited lines. You can also easily check the output of relays and controllers.
More than just a multi-function calibrator, its functions go far beyond an ordinary multi-function calibrator. It is also a loop diagnostic tool that can diagnose common problems in the loop. This is a function that other instruments of the same type do not have. Is there water in the junction box or an unknown ground fault? Our unique loop diagnostic technology makes it easy. Or use Loop Scout to view a variety of loop signals, including voltage, current, and resistance values. You no longer have to regret throwing in some good transmitters by mistake, just use them to find the problems in the loop. Act as a universal transmitter, then turn on the loop diagnostics and our display will tell you exactly what the sensor is inputting. This problem may occur if there is uncontrollable current flow in the circuit causing a ground fault, which may occur if the wiring is corroded or water has entered the circuit. If there is no problem with the control system, the thermal resistance function of the damaged transmitter can be replaced to quickly and automatically detect two-, three- and four-wire connections and alarm for sensor problems. This is our unique patented technology, patent number.
Simple and easy-to-use multi-function calibrator
& Friendly operation interface and method
The double-click menu is more intuitive and easier to set up. Multifunctional calibrators are comparable to single-function calibrators in terms of ease of use. In a dark environment, the backlight of the screen can be turned on to make the data clearly visible.
& Calibrator parameters
Accuracy.% reading + .Full scale
& Measure temperature sensor, frequency pickup, loop current, voltage value and pressure
Check the sensors in the loop value, the maximum and minimum values are memorized immediately, and the variability of the loop can be analyzed.
&Guaranteed process input compatibility
Compatible with the instrument you use, including all brands of smart sensors and various thermocouple and thermal resistance types.
&Quickly set three output values and can automatically step the ramp
Use the adjustment knob to quickly set any value, and you can also store any three output settings, and you can also use the conversion switch to adjust the values. Instantaneous reappearance. You can choose between, & step to automatically increase the output value to %, %, or % of the span. Set the ramp to smoothly increase or decrease the output between zero and span. Set the step/ramp time between and seconds to match the user's system.

Characteristic Parameters
Milliamp Calibration
& Easy to Operate
Use the multi-function calibrator to calibrate and measure all milliamp DC loop signals, and detect the Current signal at any node.

&DC voltage& has three output ranges
Using it, you can check calibration and measure all DC millivolt signals, with ranges of millivolts, . . millivolts, . . millivolts< br/>
&Calibrate flow meters and frequency calibrators
Check, calibrate, and measure zero-crossing square waves and all frequency signal instruments, generate/measure frequency signals in the range of units/minute), . . . .
&Calibration as Loop Power
Use an analog 2-wire transmitter to check loop wiring, applicable to all loops.
&Read the loop current
Check the controller output and measure the milliamp signal. It can measure milliamperes (.%%), and the accuracy is much higher than that of the general multi-function calibrator.
&Power supply/measuring wire transmitter
When measuring the output of the wire transmitter and other loop devices, the built-in battery can simulate the output of DC to power the equipment in the process loop, and the built-in ohmic resistor can Communicates with the protocol transmitter.
&Read DC voltage
The multi-function calibrator can measure the voltage of four ranges. Frequency converter. signals and other voltage values.
&Detection Optical Pickup
There is a green indicator light that flashes synchronously with the output frequency.
& Measure frequency signal
Check the output value of the frequency process signal, instantly display the maximum and minimum values of the process variation
& Milliampere signal generator
Calibration recorder, digital Displays, travel switches, and any meter with milliamp signals. The multi-function calibrator has a built-in adjustable digital potentiometer, which can easily and quickly set the minimum change value of milliamps or set the percentage value of milliamps.
Thermocouple Calibration
Measuring Thermocouple Sensors
Locate sensor connection faults and find broken lines or corroded connections. Simply connect a miniature thermocouple connector to a thermocouple, and the model can measure the temperature in degrees Celsius or degrees Fahrenheit.
The calibration result is directly displayed as temperature ( )
The user does not need to carry any power supply or thermocouple meter with him. This model is suitable for all types of thermocouples, including , , and. The adjustable digital potentiometer can be used to quickly and easily set any value within the range, and the switch can instantly reproduce any three temperature values.
Calibrating the thermal resistance
Easy to use
This model can check and calibrate all types of thermal resistance instruments, and can also measure thermal resistance sensors. At the same time, a simple wiring diagram of the relevant connections will automatically be indicated on the display.
The calibration result is directly displayed as temperature ( )
The user does not need to carry any decade box or any resistance meter with him. This model can be applied to all types of thermal resistors, including,) & ( ) &. The adjustable digital potentiometer allows you to quickly and easily set any value within the range, and the changeover switch allows you to store any three temperature measurements and reproduce them instantaneously. This model can also be used as a decade box with measuring ranges from . to and from . to .
Used in almost all types of process instruments
No competitor’s calibrator on the market can match as many types of process instruments as we do! Just connect directly to the thermal resistance input of the smart transmitter and the multi-channel recorder to detect their output or displayed measurement values. This model is also suitable for
older instruments with fixed excitation current, as well as newer instruments that can switch the excitation current between input channels.
Measuring thermal resistance sensors
Use patented technology to locate faults in sensor connection faults and damaged lines. Just connect the user's two-wire, three-wire or four-wire thermal resistor to the phase, and the connection will be automatically detected and the temperature of the thermal resistor will be measured (displayed as ℃ or ℉).
Troubleshoot wiring and connection problems
During installation, use the built-in
continuity checker to check for wiring and continuity problems, as well as for
short circuits To position. A buzzer warning sound will sound within the range of ~
.
Pressure Calibration
With a dedicated pressure module and pressure generating device, pressure gauges, pressure transmitters and other equipment can be calibrated.