BQF-100 type mine pneumatic charger charger with great value

重量：

85kg

.Don't be afraid of hardship. Life is the result of hard work; don't avoid the ups and downs. After the storm, there will be a rainbow; don't be afraid of failure. Failure is the mother of success; don't be afraid of setbacks. Once you get over them, the road will be smooth. Believe in yourself that tomorrow will be better! Good luck with your work!
Charge charger mechanical charger mine charger
Lifting lever type stirred charger The charger is suitable for charging medium and deep holes in large underground caverns in mines. The charger adopts manual mechanical control. . The charger is suitable for loading powdery and granular ammonium oil.
The charger is an indispensable charging equipment for underground mines. The use of wind transportation has the characteristics of fast charging speed, high filling density, high charging efficiency, good blasting effect, and easy use and portability.
Using a charger to charge can save manpower, improve charging efficiency, improve blasting quality, reduce mining costs, reduce labor intensity, and ensure operation safety. Over the years, it has been used in underground mines such as metallurgy, coal mines, and building materials, and has been well received by users.
Disassembly and maintenance of the charger machine
1. Disassembly of the charger
. Unscrew the two pressure caps of the air inlet path to remove the pressure regulating valve and air inlet valve;
.Unscrew the upper bolt to remove the top cover;
.Unscrew the bottom bolt to remove the spherical discharge valve;
.Remove the elbow to adjust the rotational tightness of the discharge valve;
/>.Pull out the three small pins and the stirring handle in the barrel to take out the mixing device;
.Unscrew each connection and remove each air valve.
2. Maintenance of the charger
. Collect the remaining medicine and open the blower valve. Use the medicine transfer hose to blow off the floating medicine on the inner and outer surfaces of the barrel and wipe it clean with a rag.
. After each charge is completed, unscrew the two pressure caps of the air inlet and take the pressure regulating valve out of the well to extend the life of the pressure regulating valve.
. After using it once, there is no problem after removing the bend. Clear the remaining medicine in the dead corners;
. When the medicine charger has been underground for too long, if the operation handles are not flexible, you can slowly turn them several times to return to normal.
3. Hazards, equipment failure analysis and countermeasures during the operation of the charger
. The charger must be handled with care and it is strictly forbidden to throw or throw it;
. The charger enters the operation site The roof and the two piles of pumice must be carefully inspected and processed to ensure that they are safe before operation;
. When the charger is working, the working surface must have sufficient lighting and the air duct joints should be secure. Operators must not leave their posts;
. Before charging, the air should be turned on to blow away the debris in the air duct and the charger to prevent clogging. Check whether the charger is in good condition and whether there is any wind or other damage to prevent flying charges. Avoid bad habits during operation;
. Pay attention to adjusting the air pressure when charging. The extubation personnel should work closely with the operator. The extubation personnel should stand to the side and do not stand in the direction of the blast hole to avoid injuries from downward impact. Person;
. When sifting the medicine, use a wooden stick to hammer the medicine finely. Do not use a hammer to smash the medicine. Do not mix stones and other debris into the medicine. After the medicine is sifted, in order to reduce the powder return rate of the medicine, the amount of spraying can be -%. Mix the light diesel oil evenly and then bag it and put it in a safe place;
. When charging, pay attention to adjusting the air pressure. Extubation personnel must master the extubation technology and control the charging density to around ./ and ensure the charging length;
. Personnel placing the detonating tube when charging must pay attention to the fact that the detonating tube can only be in a straight line in the hole and must not be bent or bent;
. It is prohibited for untrained personnel to start the equipment and it is strictly prohibited for one person to work;
/>When operating in special areas, effective safety measures must be formulated and a dedicated person must be responsible for the operation.
Company spirit
: &;We speak for quality and we communicate with service.
Our advantages
:; Our products are all self-produced and sold with excellent cost performance.
；We will make all our products "fine, complete, and big."
Bottom of form
Jining Shunyuan Industrial and Mining Equipment Co., Ltd. was established in 2001 and specializes in the production of mining chargers with first-class quality and low price. Welcome to call us for consultation and purchase!
Contact person: Gao Jing
Telephone:
Mobile:
:
Ali Wangwang: