< r parameter
Name

Water seepage (/)

r Maximum water head

r Working medium

r Installation method

r Normal water pressure direction

r Door frame distance Side wall distance


< Forward

Reverse


< Copper-inlaid cast iron round gate

r

r

r forward
reverse

r water or sewage

r Plumb bob status

r Front facing water

r


< Copper-inlaid cast iron square gate


< Two-way copper-inlaid cast iron gate

r

r

r forward and reverse


< Two-way copper-inlaid cast iron square gate


Note: The gate whose water head exceeds needs to be specified separately
< Part name

Material


< Door frame gate guide rail




< Screw

r,r,,,,






<5 Instructions for selecting cast iron inlaid copper gates:
When selecting a gate, the value should be indicated (the height from the center of the gate to the bottom platform of the hoist
The hoist should be determined based on the hoisting force and degree of automation in the table. For details, please refer to the hoist sample.
The design load of the platform should be considered in both forward and reverse directions (the closing force refers to the opening force).
The shaft guide is set according to the different well depths, and should be designed in conjunction with the linkage. The shaft does not interfere
During operation, the entire screw and the coupling gate move up and down, which is called an open rod gate. When the screw does not move and the gate plate moves up and down, it is called a concealed rod gate.
Direction Bearing When selecting a pressure gate, it should be noted that when a forward pressure gate is used to withstand water pressure in any direction, the water head should With opening device, no special hoist is required
Please specify when ordering, and indicate the specific name, model and specifications of the separate gate (and supporting hoist)
Our factory can produce other materials (stainless steel Carbon steel, aluminum alloy, plastic) or special-shaped gates
Our factory's supply does not contain any embedded parts, so the gate layout refers to the previous page
The samples provided by our factory are subject to revision without further notice.
Before use, an appropriate amount of calcium-based or aluminum-based grease should be applied to the screw rod and checked every ~ month after it is put into use
Check the foam once a month when it is used frequently.
The electric hoist uses lithium grease or the corresponding grease required in the "Valve Electric Device Instructions"
The grease should be checked and added once a year.
Manual hoists (handwheel type and hand-cranked type) both open the gate counterclockwise and close it clockwise
It should be noted that after the gate is closed in place, no more force should be used to prevent the screw rod from bending.
When the electric hoist is operated manually, the switching handle should be moved to the manual position. After the manual operation is completed,
the handle must not be moved back to the electric hoist. It will automatically switch.
The wiring and debugging work of the electric hoist shell must not be done on rainy days. After the adjustment is completed, the shell should be covered.
Pay attention to the sealing effect. The debugging work should be done immediately after opening the cover. Do not open the cover and debug it overnight. Electric hoists are all short-time working systems and the continuous debugging time should not be too long. Even gates that are used infrequently are recommended to be run at least once a month. After the gate is installed, it is strictly prohibited to carry out secondary grouting with the gate body open. The water flow test shall not be carried out before the hoist is installed on the rear edge of the gate.
When installing the gate, it should be noted that the reverse water pressure in the direction of the water pressure the one-way gate withstands must not exceed the specified
value.
The gate is usually made of cast iron or ductile iron, which has better corrosion resistance. Usually, anti-corrosion work is carried out
once every year. When the medium is highly corrosive, the anti-corrosion period should be determined according to the specific circumstances.


: > < ) << )Hebei Qianqian Hydraulic Machinery Factory is a professional manufacturer of hydraulic hoists, gate cleaners and construction equipment. As a manufacturer of winches, our factory covers an area of square meters and has production lines such as turning, planing, milling, and cold work sheet metal casting. It has a complete range of work types, strong processing capabilities and technical force, and is equipped with physical and chemical testing methods and equipment. Sales outlets are all over the country. And exported to Malaysia, South Korea, South Africa and other countries and regions.
<<) At present, the company has several departments and workshops: it has many formal employees, including senior engineers and intermediate engineers. It also has a complete quality assurance system and high-quality after-sales service. It has an excellent geographical location and convenient transportation. Transportation is very convenient.
<< )