Qingzhou mining chute, Shandong gold processing equipment, Shandong placer gold chute, Qingzhou gold panning chute

& Qingzhou Mining Chute Shandong Gold Preparation Equipment Shandong Placer Gold Chute Qingzhou Gold Rush Chute
Chute gold panning uses the difference in the specific gravity of gold and sand. The slurry flows through the chute, and gold with a large specific gravity difference is deposited on the bottom layer, while sand with a smaller specific gravity floats on the bottom. The upper layer is washed away with the current. The new gold selection chute uses gold panning felt to extract gold. Due to the hardening of the chute and the siltation of the chute, the net gold selection rate of the gold panning felt is only
%
. Due to these weaknesses, the gold panning chute has been developed in a targeted manner. In order to suppress the pressure
its bottom plate is made of rubber plate, and it is mechanically tortured to compress the sediment and solidify, thereby increasing the gold selection rate to more than
%
.
Mineral gravity separation equipment, manufactured by Chinese engineers, is used for the extraction of placer gold ore. It has obvious achievements in selecting capillary gold and thin-skinned gold. It has a simple structure, reliable operation, few faults, low energy consumption and low water consumption. It is a powerful tool for panning placer gold deposits.

Mineral gravity separation chute equipment is mainly used for the selection of placer gold ore. It has a very good effect on capillary gold and thin-skinned gold. It has a simple structure, reliable operation, few faults, low energy consumption and low water consumption. It is a powerful equipment for panning placer gold ores. It can also be applied to other gravity separation. It effectively overcomes the hardening phenomenon of the chute, reduces the siltation phenomenon, and significantly improves the recovery rate of fine-grained gold.
Working principle: Chute gold panning utilizes the difference in specific gravity between gold and sand. The slurry flows through the chute, and gold with a larger specific gravity is deposited on the bottom layer, while sand with a smaller specific gravity floats on the upper layer and is discharged from the work area with the water flow. The original fixed chute used gold felt to extract gold. Due to the hardening of the chute and the siltation of the trough, the net selection rate of gold extracted from the gold felt was only about %. These shortcomings were overcome by the agitated chute with its bottom plate. Made of rubber plate, the bottom plate is mechanically agitated to slowly agitate to overcome the hardening of sediment. It is agitated periodically to complete stratification and sand discharge, thereby increasing the net separation rate to about %.
The main features of the mining gold mining chute: large gold ore processing capacity

no power, which can save mineral processing costs

reasonable structure, high strength, and can It has strong disassembly and assembly properties and is easy to transport and relocate

The gold mining recovery rate is high, and the recovery rate can reach %. It can not only recover granular gold flake gold, but also recover particulate gold

It has strong adaptability and can be used for mineral processing in ore bodies under any conditions.
, placer gold purification equipment
Placer gold extraction equipment mercury paste separator equipment is a centrifugal gold separation equipment. It is suitable for the recovery of single gold from placer gold, vein gold ore and polymetallic ores, replacing mercury plates. It is an ideal choice for gold panning and rock gold equipment on dry land or rivers. The mineral processing test has proven that the recovery rate of alluvial gold is above %. Especially when recovering the single gold in vein gold ores, when the grinding particle size is less than .%, the recovery rate of single gold can reach more than %. For. The recovery rate of single gold is over %. The ore discharge cycle for rock gold is 1 hour, and the alluvial gold is 1 hour, and the enrichment ratio can be up to 2 times.
Zhongtai
The main products of Zhongtai Machinery are:
Gold mining boats (sand pumping type, bucket type, cutter suction type, etc.), gold mining equipment, gold mining machinery, gold selection equipment, gold selection machinery, Water jacket centrifuge, alluvial gold equipment, alluvial gold machinery, mercury evaporator, gold rush, automatic washing machine, dry land alluvial gold equipment and more than dozens of products for you to choose from. The company also produces magnetic separators, iron sand ships, sand mining machinery, dredgers, sand screening machinery, sand washing machinery, stone washing machinery, crushers and other products. Products are widely used in: sand fields, metallurgy, mining, river port dredging, water conservancy and mining and other industries.

The company follows the principles of cooperation, harmony, development and win-win
&r
and has established deep friendship and good relationships with suppliers across the country. In order to seek development in the ever-changing market economy, we adhere to the management of integrity, brand, service and innovation
&r
> Concept, co-create brand, build harmonious marketing, and establish a win-win strategic partnership.
Qingzhou Zhongtai Mineral Sand Machinery Co., Ltd. warmly welcomes new and old users to negotiate and make friends all over the world. We hope to create a brilliant tomorrow together
!

Gold selection chute< br/>Mining chute
Mining chute
Gold dressing equipment
Alluvial gold chute
Gold panning chute
Gold mining chute
Gold dressing machinery
Mining Equipment
Shandong gold selection chute
Small gold selection equipment
Gold dipping chute
Chute gold selection