Which wood pellet machine manufacturer is the best?

功率：

90KW

&As we enter autumn, the weather will become cooler and cooler. Since the days and nights are the same in autumn, many people also pay attention to taking care of their bodies at this time. So, is there anything we need to pay attention to with the straw pellet machine? How to operate the straw pellet machine reasonably? Below, the editor of Shandong Yuguan Machinery will give you a brief introduction: 1. Operators should not wear gloves and should stand on the side of the biomass pellet machine when feeding materials to prevent rebound debris from hurting the face.
The crushed materials should be carefully inspected to prevent copper, iron, stones and other hard objects from entering the crushing chamber and causing accidents.
When working, you should always pay attention to the operation of the straw pellet machine. The feeding should be even to prevent clogging and boring of the machine. Do not overload the machine for a long time. If any vibration, noise, excessive temperature of the bearings and body, or material spraying are found, stop the machine immediately for inspection and troubleshoot the problem before continuing to work.
After the crushing table is started, it will idle for one minute and then start feeding after there are no abnormal phenomena.
Do not replace the pulley casually to prevent the crushing chamber from exploding due to excessive rotation speed, or too low rotation speed affecting work efficiency.
For long-term operation of the straw pellet machine, it should be fixed on the cement foundation. If the working location is often changed, the straw pellet machine and the electric motor should be installed on a base made of angle iron. If the straw pellet machine is powered by diesel, the power of the two should be matched, that is, the power of the diesel engine is slightly greater than that of the pulverizer. power, and make the pulley grooves of the two wheels consistent and the outer end faces of the pulleys on the same plane.
After installing the straw pellet machine, check the tightening condition of each fastener. If there is any looseness, tighten it.
Check whether the belt tightness is appropriate and whether the motor shaft and the straw pellet machine shaft are parallel.
Before starting the straw pellet machine, first turn the rotor by hand and check whether the claws, hammers and rotor are running flexibly and reliably, whether there is any collision in the shell, and whether the rotation direction of the rotor is consistent with the direction pointed by the arrow on the machine. Whether the motor and wood pellet machine are well lubricated.
&The above are the precautions for the operation of the straw pellet machine summarized by the editor. Here I wish all of my friends good health and happiness during the autumnal equinox!
&Yuguan wood pellet mill advantages:
1. Wood pellet mill structure. First of all, everyone must understand that the structure of wood pellet machine equipment is divided into vertical, horizontal and flat dies. Currently, it is the most professional and most professional. The mature structure is the vertical ring die. The vertical ring die is the most professional model used for biomass production in the wood pellet machine industry. The horizontal ring-die wood pellet machine was transformed from the equipment used to process feed pellets. It cannot press wood pellets very well. The flat die is professionally used to make cattle and sheep feed. It is better for straw and soft materials, but if it is pressed Some hard miscellaneous wood cannot be pressed out and is almost shapeless.
2. The structure of the wood pellet mill. Therefore, a vertical ring-die wood pellet mill is used to make biomass. The first is the structure of the vertical ring-die wood pellet machine: the main structure of the wood pellet mill: feed cover, The dial plate, granulation chamber, bearing chamber, and base are just the external structure. Of course, there are also many internal parts, such as molds, pressure rollers, spindles, etc.
3. Wood pellet machine material. A strong wood pellet machine manufacturer will use steel from major manufacturers, such as Baosteel, Jigang, Laigang, etc. Yuguan Machinery uses these three major steels. Factory material.
Fourth, heat treatment of wood pellet mills. High-quality wood pellet mills must undergo heat treatment, and there are many parts that require heat treatment, such as hollow shafts, molds, pressure rollers, briquettes, granulation chambers, etc. Bearing chamber, tightening bolts, spline shaft, eccentric shaft, etc. However, some informal or weak wood pellet machine manufacturers only have the main shaft and mold for heat treatment. After heat treatment, the parts not only have an increased service life, but also have a much stronger hardness and flexibility, which greatly increases the stability of the equipment. Therefore heat treatment is very critical.
If you want to do a good job in biomass projects, you must choose a good wood pellet mill manufacturer. Yuguan Machinery is your best choice.