11 common car fault repair tips-[Xinxiang Used Cars]

& Tips for repairing common car faults [Xinxiang Used Cars]
When driving outside, it is inevitable that some temporary faults will occur. In the urban area, it is quite convenient to go to the store or call for rescue, but if we are in the suburbs or out of town, some water from far away cannot quench our thirst nearby. The so-called "long-term illness makes a doctor", in fact, car owners can also master some simple emergency repair methods, which may be able to support them until rescue comes at a critical moment.
Xinxiang Used Cars
It was established in 2010 and has been in business for more than 10 years now. It has its own place in the second-hand car industry, and it goes without saying much about its qualifications. Company C Gao Xiaozhong has been working in the second-hand car market for more than ten years. He has very rich experience in second-hand cars and has also accumulated his own personal connections.
Tip: Shake when starting the car in the morning
Because some cylinders are not working well and the valves are not closed tightly, you can run at high speed in the upper or lower gears for a while. If the car does not vibrate when it is hot but the gear shifting is not smooth, it is possible that the fuel injection nozzle is uneven and needs to be inspected and cleaned.
Trick: I feel that the brakes are not as effective as before
When waiting for a red light, apply the brakes a few times and it will be effective.
Trick: Vehicle deviation
Increase the air pressure of the front wheel in the direction of deviation or lower the air pressure of the tire in the other direction.
Trick: When igniting the car in the morning, it is found that the battery energy is insufficient and it is difficult to start.
Pour a bottle of hot water on the battery and turn off all electrical equipment, including closing the car door. Wait for a few minutes to start the engine, then drive and replace the battery.
Tricks: The door handle is loose or the key becomes tight and astringent
Open the front door and you will see a plastic cover on the side. Open it and you will see a screw inside. Loosen it a few times and it will start. The lock core can be pulled out from the outside. There is a pull cord on the handle inside, and the tension of the pull cord can be adjusted. The screws of the rear door are blocked with sealing strips and can be opened by hand. Before installation, grease the inside of the lock cylinder so that the handle and lock on the door can be restored easily and as before.
Tip: Fuel tank damage
When a motor vehicle is in use, especially when driving in areas with poor road conditions, damage to the fuel tank may occur. If you find that the oil tank is leaking, you can wipe the leakage area clean and apply soap or bubble gum to the leakage area to temporarily block it. If possible, repair with epoxy resin adhesive, the effect will certainly be better.
Trick: Oil pipe rupture
When the oil pipe ruptures, you can wipe the rupture clean, apply soap, wrap a cloth or tape around the rupture of the oil pipe, tie it tightly with iron wire, and then apply a layer of soap.
Trick: Broken oil pipe
When the oil pipe is broken, you can find a rubber or plastic pipe that is suitable for the diameter of the oil pipe to connect it. If the socket is not tight enough, tie the two ends tightly with iron wire to prevent oil leakage.
Tip: Oil pipe joint leaks
When using a motor vehicle, if the engine oil pipe joint leaks oil, it is mostly caused by the oil pipe bell mouth and the oil pipe nut not sealing. You can wrap cotton yarn around the lower edge of the horn, and then tighten the oil pipe nut and the oil pipe joint. You can also chew bubble gum or maltose into a paste, apply it to the oil pipe nut seat, and wait for it to dry and solidify to act as a seal.

Tip: The inlet and outlet hoses are broken
When the rupture is not serious, you can wrap the leaking area with a cloth coated with a layer of soap. If the rupture is large, cut off the rupture of the hose, put a bamboo or iron pipe in the middle, and tie it tightly with iron wire.

Tip: The fan belt is broken
You can tie the broken belt in series with iron wire or use the method of starting and stopping to drive the car away.