Electric concrete sleeper bolt drilling machine supplier_Product Introduction_Jinzhou Shuangxing

Electric Concrete Sleeper Bolt Drilling Machine Supplier_Product Introduction_Jinzhou Shuangxing
With the rapid development of my country's railway transportation, higher requirements have been put forward for line construction and maintenance. According to different places of use, different road maintenance equipment is equipped, which greatly improves the work force and completely replaces manual work. Now the market prices are chaotic. Our factory adopts the lowest price on the basis of unchanged quality and gives more benefits. Wholesalers can get more benefits and are committed to developing more markets. Welcome to negotiate.
Electric concrete sleeper bolt drilling machine supplier_Product introduction_Jinzhou Shuangxing
Liaoning Shuangxing has twenty years of professional manufacturing
Customer consultation
Contact manager Zhang
Address Anshan City, Liaoning Province
Office
Fax
Technical Service
Striving to create the industry-leading brand Liaoning Shuangxing
Electric concrete sleeper bolt drilling machine supplier_Product Introduction_ Jinzhou Shuangxing
Detailed parameters
Electric concrete sleeper bolt drilling machine supplier_Product Introduction_Jinzhou Shuangxing
Preparation before rail drilling machine operation
The installation of the drill bit shall be based on the on-site work If required, install a core drill bit or twist drill bit. The specific method is as follows
This manual takes the installation of a hollow drill bit as an example. Push the feed lever ⑨ toward the gasoline engine to the end.
Then lift the clamp lever ⑥ toward the gasoline engine.
Lift the drilling machine, use a wrench or your fingers to loosen the set screw at the spindle sleeve, install the drill bit core into the drill bit, then align the two flat parts with the two set screws, and insert the flower. After inserting it into the key shaft and being close to the root of the spline shaft, tighten the set screw to complete the installation. This machine is shipped with a hollow drill bit from the factory.
Drill bit removal: Lift the drilling machine according to the above steps, use a wrench to rotate the bolt counterclockwise, and remove the drill bit from the spindle sleeve.
After the operation, you must use the wrench that comes with the machine. If you use other wrenches to cause damage to the machine, you will be responsible for the consequences. Remove the drill bit and apply thin oil or rust inhibitor to the threaded hole.
Installation of positioning blocks
Choose the positioning block with the same rail model as the one given. ⑩ This positioning block is a combination dual-purpose positioning block, that is, and, and combination, respectively marked with, and the number is close to the side of the rail , indicating which rail type is to be drilled.
How to use the water injection bucket
Align the handle with the groove at the mouth of the water injection bucket and press down to the root. Rotate the handle counterclockwise until the pressing device is unscrewed. Then add coolant into the water injection bucket to prevent If the drill bit and the drilled rail hole are rusty, fill up the coolant and tighten it clockwise, then rotate it counterclockwise at a small angle, take it out from the slot at the mouth of the water injection bucket, press the handle back and forth a few times to pressurize the bottom of the water injection bucket. Insert the water pipe into the oil pipe in the fixture of the drilling machine. Hold the handle of the water outlet valve of the water injection bucket, press the water valve downward with your thumb, and push it forward to open it. At this time, press down on the drill bit core and make sure the coolant flows out of the drill bit before proceeding to the next step.
Introduction and installation of positioning ruler
This positioning ruler is divided into equal models, and the corners of the positioning ruler are marked respectively. Each positioning ruler has a positioning groove, which is processed according to the standard hole spacing of the rail.
Pull the ruler locator back, insert the locator ruler ⑤ into the clamp body, and go under the first groove.
Fill in fuel and lubricating oil
To fill in fuel, first unscrew the fuel tank cap, add the above unleaded gasoline or ethanol gasoline, then tighten the fuel tank cap,
Fill in lubricating oil First unscrew the fuel tank cap of the lubrication chamber, add gasoline engine oil in summer, and gasoline engine oil in winter until it reaches the scale mark. Do not add less or excessive gasoline oil, and tighten the fuel tank cap. Use your fingers to press the carburetor storage bubble of the gasoline engine a few times until the carburetor storage bubble is filled with gasoline.
When the temperature is lower than ℃, usually first close the damper and lift it up, increase the throttle to /, quickly pull the starting disk, and slowly put it back. After the gasoline engine starts, slowly open the damper to the maximum direction. Press down, slowly increase the throttle, idle for a few seconds, check whether the transmission part is flexible, whether there is any abnormal noise, whether the screw connection is loose, press the gasoline engine stop button, and prepare to drill.
Electric concrete sleeper bolt drilling machine supplier_Product Introduction_Jinzhou Shuangxing
After-sales Service Commitment
Uphold a full range of high-quality and fast service standards for the company, with customer satisfaction as the goal , hereby make a public commitment.
One Service Commitment
Our company has established a group of tough emergency maintenance service teams with experienced field engineers and senior technicians who can rush to the scene as soon as possible for any problems that arise. , perform repairs and replacements.
Within one week of product delivery, the staff of our company's after-sales service department will conduct telephone follow-up consultation based on the customer's contact information until the customer is satisfied.
All complaints about product quality will be answered within hours, and we will rush to the scene within hours, and determine the handling measures according to the complaints, and carry out repairs and replacements.
Our company promises that all maintenance personnel will be on call to better solve customers' problems.
Expenses related to product quality during the warranty period will be borne by our company.
During the warranty period, we will provide free repairs due to improper use by you or caused by the natural environment. The materials and accessories used in the repairs will only be charged at the cost price.
For products beyond the warranty period, our company promises lifelong regular on-site inspection and maintenance.
Two transportation methods
All goods are delivered to customers free of charge, and installation, debugging and installation and maintenance are free of charge. Maintenance personnel inform customers of common sense on how to perform product maintenance until the customer is satisfied.
After all goods are installed and debugged, the customer can leave the site only after checking and accepting them.
Three Returns and Exchanges of Goods Commitment
The returned products must have complete outer packaging accessories, instructions, warranty cards, receipts and delivery notes, and a description of the reasons for return or exchange.
If users have quality problems under normal use, please contact our company quickly during the warranty period to facilitate timely repair and replacement.
Now you cannot enjoy our company's return and exchange commitment in the following situations.
The product has been used abnormally.
Storage moisture under abnormal conditions.
Unauthorized repairs.
Normal wear and tear of the product.
Expired.
The final interpretation right of this service commitment belongs to Liaoning Shuangxing Machinery Equipment Co., Ltd.
Liaoning Shuangxing produces and sells the following products
☆Railway vehicle internal combustion tamping pick tamping machine hydraulic rail hole extrusion machine hydraulic rail drilling machine manual rail drilling machine rack type track starter hydraulic track starter Rail cutting machine, square sleeper, hydraulic straight rail device, rerailer, universal gauge ruler, rail grinder, square gauge rail truck, etc.
☆Track accessories, bezels, turnouts, turnout accessories, turnout tie rods, rail gauges, rail gauges, rail gauges, rails Anchor rod b Anchor rod drill rod b pneumatic drill rod switch pad track plywood track spike insulating splint crossing switch pad composite rubber pad track fixing rail gauge tie rod guard rail buckle plate line buckle plate base insulated gauge Rod buckle plate, twist drill pipe, coal drill pipe, twist drill pipe, connection collar, chain spreader, draft drill, anchor rod, pallet, nylon baffle seat, manual switch, manual bender, bender, bender, rail press, pressure plate, fish tail plate Fishtail bolts, etc.
Liaoning Shuangxing sales network Hebei Shanxi Inner Mongolia Liaoning Jilin Heilongjiang Beijing Tianjin Shanghai Jiangsu Zhejiang Anhui Fujian Jiangxi Shandong Henan Hubei Chongqing Sichuan Guizhou Yunnan Shaanxi Gansu Ningxia Xinjiang and other places.
Note: The above content is provided by Liaoning Shuangxing Railway Machinery Co., Ltd. The relevant product parameters and pictures are for reference only. Specific products may have different origins due to different production batches. Please contact the sales staff for specific details.