Formwork partition board production line equipment

规格：

可定制

型号：

各种

The features of the molded lightweight partition board equipment are plastic core tubes, which do not need to be washed away, and the electric pipe extraction is not limited by time.
Can be adjusted to any length, one machine can be used for multiple purposes.
Automatic opening and closing of mold, automatic temperature control.
Small investment, simple operation and convenient maintenance.
Strong mechanical properties, double-sided molding precision, high thickness, accurate flatness and good flatness.
It requires less labor, occupies less space, is flexible and can be used for on-site production.
Providing one-stop services such as production of complete sets of technical formulas, installation and construction processes, and technical inspection data certificates. This equipment has passed the appraisal of scientific and technological achievements and has been designated as a promotional product.
Feasibility Analysis
Patented products have high technical content, low investment, high output, short cycle and fast returns.
Low investment: This project has low investment and high output. The efficiency is good, the cost profit margin is large, and the output value profit margin is high.
The market is good. New wall materials have broad prospects and obvious competitive advantages. Good performance: This product can fully meet various performance requirements of non-load-bearing lightweight walls.
Good policy. This project has the advantages of energy saving, consumption reduction and waste recycling. It is in line with policy guidance and is strongly supported by the state.
It is of great practical significance for enterprises to upgrade and transform and develop building energy conservation, as well as protect water and soil resources, maintain ecological balance, etc.
Investment Analysis The conditions for building a lightweight partition board production line with an annual output of 10,000 square meters are based on panels as an example
The area is square meters, and the factory building is square meters.
The comprehensive local price plan for production water and electricity is/square meter.
Enterprise employees
Production process
Send the raw materials to the mixer according to the proportion through the conveyor belt and manually mix them evenly through the mechanical mixing machine
Automatic injection machine
Manual edge closing
Piping machinery
The products are rolled off the production line and stacked
installed and used.
Functional features
The mold erection lightweight partition board equipment adopts hydraulic control and electrical control systems, hydraulic mold opening and closing, automatic temperature control, and a high degree of mechanization and automation
Both electricity and water vapor can be heated and dehydrated. Fast molding and short maintenance cycle.
The molding cavity has high structural rigidity, high plate making precision, and good thickness accuracy
The plastic core tube is lined with metal tubes, which is durable and does not need to be washed. The electric pipe extraction saves labor and time
Continuous mesh design, uniform mesh distribution, accurate and convenient
One machine with multiple functions, adjustable length and thickness of wall panels, suitable for producing various lightweight boards such as magnesite gypsum ceramsite
Mature equipment technology, stable and reliable , good durability. The utility model belongs to a wall panel forming device, in particular to a wall panel forming machine. It includes a hydraulic press mold car, which is characterized in that the interior of the mold car is divided into isolation cavities by an isolation plate. A core-pulling hole is longitudinally provided on the front baffle of the mold car, and a bolt hole is also provided on the upper side of the baffle, through which the bolts are connected to the left and right. The baffle is fixed, and the bottom of the mold car is connected to the baffle. The beneficial effect of the utility model is that the arrangement of the core-pulling holes makes the processed wall panels contain sound-insulating holes, and the produced wall panels are light in weight and have good sound-insulating effects. The use of isolation panels can improve work efficiency, and multiple wall panels can be formed at one time.
Each group of molding insulation board equipment can produce one wall panel at a time. All demoulding can be completed in less than an hour, and the efficiency is as high as you can imagine
The three-dimensional mold insulation board equipment has a wide production range
It can widely produce a series of lightweight partition boards. This production line is a multi-purpose production line. Including pure foam lightweight partition panels, foam sandwich lightweight partition panels, inorganic non-combustible exterior wall insulation panels, fire door core panels, etc.
Product Features of Mold Insulation Board Equipment
Energy-saving insulation adopts Australian advanced technology and is made of lightweight materials such as reinforced calcium magnesium board and polystyrene particle cement, which are made of high-pressure composites. It has good thermal insulation effect and is more than energy-saving. /National exterior wall standards, there is no disadvantage of adding insulation boards after laying bricks.
High strength and high strength bending failure load can reach more than three times the self-weight of the wall panel, exceeding the national standard.
Impact resistance It has impact resistance and meets the national standard.
  Low investment This project has low investment and high output. The efficiency is good, the cost profit margin is large, and the output value profit margin is high.
The market is good. New wall materials have broad prospects and obvious competitive advantages. Good performance: This product can fully meet various performance requirements of non-load-bearing lightweight walls.
Good policy. This project has the advantages of energy saving, consumption reduction and waste recycling. It is in line with policy guidance and is strongly supported by the state.
It is of great practical significance for enterprises to upgrade and transform and develop building energy conservation, as well as protect water and soil resources, maintain ecological balance, etc.
Investment Analysis The conditions for building a lightweight partition board production line with an annual output of 10,000 square meters are based on panels as an example
The area is square meters, and the factory building is square meters.
The comprehensive local price plan for production water and electricity is/square meter.
Enterprise employees
Production process
Send the raw materials to the mixer according to the proportion through the conveyor belt and manually mix them evenly through the mechanical mixing machine
Automatic injection machine
Manual edge closing
Piping machinery
The products are rolled off the production line and stacked
installed and used.
Functional features
The mold-setting lightweight partition board equipment adopts hydraulic control and electrical control systems, hydraulic mold opening and closing, automatic temperature control, and a high degree of mechanization and automation
Electricity and water vapor can be heated and dehydrated. Fast molding and short maintenance cycle.
The molding cavity has high structural rigidity, high plate making precision, and good thickness accuracy
The plastic core tube is lined with metal tubes, which is durable and does not need to be washed. The electric pipe extraction saves labor and time
Continuous mesh design, uniform mesh distribution, accurate and convenient
One machine can be used for multiple purposes, the length and thickness of the wall panels are adjustable, suitable for the production of various lightweight boards such as magnesite gypsum ceramsite
The equipment technology is mature, stable and reliable , good durability. The utility model belongs to a wall panel forming device, in particular to a wall panel forming machine. It includes a hydraulic press mold car, which is characterized in that the interior of the mold car is divided into isolation cavities by an isolation plate. A core-pulling hole is longitudinally provided on the front baffle of the mold car, and a bolt hole is also provided on the upper side of the baffle, through which the bolts are connected to the left and right. The baffle is fixed, and the bottom of the mold car is connected to the baffle. The beneficial effect of the utility model is that the arrangement of the core-pulling holes makes the processed wall panels contain sound-insulating holes, and the produced wall panels are light in weight and have good sound-insulating effects. The use of isolation panels can improve work efficiency, and multiple wall panels can be formed at one time.