Chongqing Living Wall Paint Complete Guide Diebian Decoration Brothers Gang

>A complete guide to the acceptance of wall paints, tips from butterfly designers
A guide to the acceptance of fine and smooth painted walls
Whether the effect of wall paint is meticulous, smooth, non-shedding, or moldy mainly depends on the paint. The quality and construction technology, especially the treatment technology of the wall base. Therefore, the acceptance of wall paint should start from the base layer. Before it is painted, it should be inspected and accepted again after painting.
Acceptance of the wall base. Base treatment is a key link to ensure construction quality. Ensuring that the wall is completely dry is the most basic condition because the mortar used as cement binding material is highly alkaline before it hardens. At this time, latex paint is applied. It must be anti-alkaline. When the alkalinity value of the cement mortar drops significantly after hardening, latex paint can be applied. The drying time varies depending on climatic conditions and should generally be left for more than a day.
Acceptance of wall paint film The types and colors of materials used for latex paint conform to the design requirements. The color of the painted surface is consistent. Quality defects such as leakage, peeling off, peeling, and color bite are not allowed. If the spray points are evenly spaced and even, no dripping or dripping is allowed, the paint film will be smooth and will not fall off when touched by hand. Doors, windows, lamps, furniture, etc. will be clean and free of traces of paint.
Key points and standards for acceptance
You should stand away from the wall and observe that there are no blisters, biting, color runoff, color difference, etc.
It should be painted evenly and firmly, and no leakage should be applied to the bottom to peel or rust.
Precautions for coating construction: Use a roller to paint the corners of a large area and use a hand brush to improve the painting efficiency and ensure the quality of the paint. During construction, latex paint must be stirred thoroughly before it can be used for its own color matching. When coloring, alkali-resistant and light-resistant color pastes must be selected and mixed into the paint liquid. It is prohibited to mix dry color powder into the paint liquid. The latex paint that has been mixed with color slurry must be stirred for at least 10 minutes to achieve a uniform color before construction.
2. Key points for acceptance of smooth and neat brick walls
The wall decoration of the kitchen and bathroom is mainly based on ceramic tiles. The wall tiles should be flat, solid and neat. There are several steps and criteria for accepting the construction of wall tiles.
Common problems and solutions for wall tiles
The main reasons for the hollowing out are insufficient bonding material, insufficient soaking of the bricks and unclean treatment of the base layer. During construction, the sleeve bricks must be clean and soaked for no less than an hour. The bonding thickness should be controlled within millimeters and must not be too thick or too thin. When pasting, make sure that the surface tiles and the bottom layer are tightly pasted, and you can tap lightly with a wooden hammer. When a hollow occurs, the wall tiles should be removed and the original bonding mortar should be removed and repaired with cement mortar that accounts for the total volume of glue.
The main reasons for uneven joints are differences in brick specifications and improper construction. During construction, facing bricks should be carefully selected and the same size should be grouped together for one wall. Standard points must be pasted. The standard points must be as close as possible to the top of the ruler. After each line is pasted, it should be checked and corrected in time with the ruler horizontally and vertically. If the joint exceeds the allowable tolerance, the wall tiles should be removed in time for rework.
The main cause of discoloration is not only the poor quality of the ceramic tiles but also the thin axial surface and improper operation methods. During construction, materials should be carefully selected and clean water should be used to soak the sleeve tiles. Pasted cement mortar should use pure sand and cement. During operation, the remaining mortar on the brick surface should be cleaned at any time. Wall tiles that have become significantly discolored should be replaced.
Key points for acceptance of Sanpingshun's paper wallpaper paving
Wallpaper paving is a wall decoration method favored by many consumers because it has the advantages of easy construction, easy replacement, and a wide choice of colors. The most important thing for the wall where wallpaper is to be laid is to ensure that it adheres smoothly and has no gaps at the intersection of patterns, etc.
Wallpaper Acceptance Criteria
The surface of the wallpaper and wall covering after pasting should be smooth and the color should be consistent. There should be no ripples, bubbles, cracks, wrinkles and stains. There should be no traces of glue when squinting
The edges of the wallpaper and wall covering should be flat. They should be straight and neat without any paper burrs
Wallpaper and wall coverings should be tightly connected with various decorative line equipment and wire boxes
The overlapping of the inner corners of wallpaper and wall coverings should be smooth and there should be no seams at the outer corners
/> Wallpaper acceptance method After the wallpaper construction is completed, stand outside and visually inspect the paper. There are no obvious seams or inconspicuous flowers. The flowers are neatly pasted and firmly pasted. There are no gaps, hollows, warped edges, wrinkles, spots, dirt, burrs, glue marks and indentations. There are no yin and yang corners. seam.
Another situation that needs to be noted is that some wallpapers have seams that can be seen when viewed against strong light due to their pattern or color, which is unavoidable. Light-colored or thick-textured styles basically do not have the above problems in terms of visual effects.
Precautions for laying wallpaper: When starting to lay wallpaper, squeeze the two sides of the two pieces of wallpaper with adjacent joints to match them, then use a scraper to press the joints and clean up the extruded glue. After the wallpaper is pasted, use a scraper to flatten the pasted wallpaper from top to bottom.
Wallpaper Maintenance Tips
To deal with wallpaper mildew, you can first wipe the wall with a dry cloth, then add half a bottle of disinfectant to a paper cup of water, or use diluted professional wallpaper cleaner to mix evenly and then wipe it. Mildew stained walls.
If moisture causes the wallpaper to warp, you can use professional wallpaper glue to paste it and press it with a flat object such as a book or a table tennis bat. If there is bubbling, you can use a sewing needle to poke a small hole in the blistering position on the wallpaper surface to release the gas. Take an appropriate amount of adhesive and put it into the hole of the needle to stick it tightly. Finally, flatten it with a flat book and let it dry.
If the edge of the wallpaper is warped due to dry cracking, if that doesn't work, you can use a syringe to inject glue into the edge of the crack in the wallpaper and try to stick the wallpaper firmly again. Or use wallpaper adhesive powder to apply to the curled edges, smooth out the warping, blow with a hair dryer for about a second, then press firmly with your hands until it is firmly adhered, and blow with a hair dryer until dry. When repairing, be sure to first determine whether there is a problem with the base layer. Be sure to extend the repair area to extend the repair area from the center of the cracked area to the vicinity.