DYTP electro-hydraulic push rod parallel electro-hydraulic push rod

Electro-hydraulic push rod parallel electro-hydraulic push rod
Corner type electro-hydraulic push rod
Electro-hydraulic push rod manufacturer
Electro-hydraulic push rod, that is, electro-hydraulic push rod, is suitable for It performs reciprocating push-pull linear (or reciprocating rotation at a certain angle) motion. It can be used in places where work objects are raised, lowered, or clamped. It can also be used in remote and high-altitude dangerous areas, and can be networked with a computer for centralized (program) control. Now it is widely used in metallurgy, mining, coal, electric power machinery, food, cement, chemical industry, water conservancy and transportation and other departments. It is an indispensable universal power source.
Working principle
The electro-hydraulic push rod uses an electric motor as the power source, and the electric motor rotates in the forward (reverse) direction, so that the hydraulic oil outputs pressure oil through the two-way gear pump, and is sent to the working cylinder through the oil circuit manifold. , to realize the reciprocating motion of the piston rod. Advantage
It has automatic overload protection function. When the electro-hydraulic push rod is working, if the external force on the piston rod exceeds the rated output force or the piston has reached the end point, the motor is still rotating. At this time, the oil pressure in the oil circuit increases to the set value. pressure, the relief valve overflows quickly and accurately to achieve automatic overload protection. Although the motor is rotating, it will never burn out. The oil circuit integrated block of the locking function electro-hydraulic push rod is designed with a pressure self-locking mechanism. When the motor stops rotating, the piston rod immediately stays in a certain position, and the pressure oil is in a pressure-maintaining state. The step adjustment can be steplessly adjusted according to user requirements within the rated speed, output force and stroke range
Model description The electro-hydraulic push rod is mainly composed of the type of the push rod, the protection level of the motor, the rated output force, the stroke, the rated speed and the use It is composed of six basic elements such as angle, and can also be equipped with three adjustment functions according to special requirements, namely speed adjustment, push-pull force adjustment, and stroke adjustment (stroke switch positioning). Except for the above three adjustment functions, which must be clearly stated when ordering, please refer to the model preparation method and fill in the six major elements carefully. Technical parameters of type parallel electro-hydraulic actuator
Precautions during installation and use
The electro-hydraulic actuator must be installed with enough space and the ambient temperature should be between 10°C and 10°C (high temperature environments must be specially ordered).
Users can configure the limit switch according to control needs.
Before installing the electro-hydraulic push rod, place it flat on the ground. Inject hydraulic oil (brand grade) and the oil level should be at the lower edge of the observation port. The oil level of the split push rod should be within the box.
The exhaust screw ring of the exhaust hole should be loosened before use.
Try booting the computer during installation.
Integral push rod, connect the power supply to operate
Split push rod, connect the power supply to allow the cylinder to reciprocate several times without load to discharge the air in the cylinder and oil pipe. Load
Maintenance of electro-hydraulic push rod
In order to ensure the service life of the high-pressure oil pipe, the oil pipe must be fixed with rubber.
Hydraulic oil should be filtered or replaced regularly, once a year or according to the actual work.
If it is not used for a long time, the insulation of the motor should be checked before putting it into use.
Simple Troubleshooting
It cannot operate when it is first installed. Check that the motor is not running or there is insufficient oil.
If it cannot operate after a period of use, remove the hydraulic control plug, clean the spool of the hydraulic control valve, and replace the hydraulic oil.
After being used for a long time, the push rod can be pushed and pulled without load, but cannot stand with load. Replace the seal for the upper hole of the piston in the cylinder. If the sealing surface leaks, replace the seal. If there is oil dripping from the extension of the oil plug rod, replace the shaft seal. Electro-hydraulic push rod pair
Our company's main business is mining products
Electric push rod
Electro-hydraulic push rod
Electro-hydraulic jaw gate, electric jaw gate, electro-hydraulic corner driver Imported material opening size
Electro-hydraulic push rod driven electro-hydraulic push rod flat gate valve
Steel wire rope core stripping machine
Electric push rod
Electric push rod
Electro-hydraulic Push rod
Explosion-proof push rod
Jaw gate
Electro-hydraulic sector gate
Belt stripping machine
Wire rope stripping machine
Single side unloader
Double-side unloader type
Broken belt catcher
Broken belt catcher for belt conveyor
Broken belt protection device Broken belt catcher
Layering Belt stripping machine
Belt conveyor offset adjuster
Chain type one-way offset adjuster
Fully automatic offset adjuster
Variable groove angle unloader
Electro-hydraulic Moving unloader
Plough type unloader
The manufacturer supplies directly and can be produced according to customer requirements. Welcome to buy!
Jining Anyuan Hydraulic Machinery Equipment Co., Ltd.
Contact Mao Yongyi
Mobile phone
Tel
Fax
Wangwang
Email
@