Supply of special rail drilling machine GZ-32Ⅰ type electric drilling machine

Supply of special drilling rig machinery for rail rails Type I electric drilling machine rail drilling machine
China's railways have a history of more than a hundred years. Over the past hundred years, the means of railway track maintenance have also evolved with the rapid development of my country's railways. It is also changing with each passing day, from the initial purely manual maintenance to small machinery to large machinery. It can also be said that the history of China's railway maintenance methods is a microcosm of the history of my country's railway development. Jining Hengwang Industrial and Mining Machinery Co., Ltd. is also constantly updating its products and improving its services under the trend of railway science and technology development. If you have any questions, you can call: at any time, Xiao Zhang will answer you!
1. Product Overview of Type I Electric Drilling Machine:
Operators must be trained and certified to work. Wear protective glasses, gloves and minimum protective equipment when working.
Before operation, check whether the machine is operating normally, whether the drill bit is clamped, and clean the remaining chips in the drill bit. Is the cooling system normal?
2. Parameters of type I electric drilling machine
Voltage:
Power:
Drilling range: -
Dimensions:
Weight:
3. Operating Procedures
Check whether the power cord of the motor is damaged or leaking electricity. Turn on the power of the motor and run it without load to see if it is normal.
Is the gearbox lacking lubricating oil?
3. Select the positioning block of the same type as the rail to be drilled, and install it at the corresponding position on the drilling machine fixture.
Turn the feed handle clockwise, first retract the spindle to the end, and then install the ground drill bit into the drill chuck and lock it.
4. Inspection during operation
Place the clamp on the top surface of the rail, adjust the appropriate length of the jackscrew, and press down on the clamp handle to lock it. If the locking strength is not enough, turn the jackscrew handle clockwise until it is locked.
. Turn on the power of the motor and let it idle for 3 seconds. When the motor runs smoothly and there are no abnormalities, rotate the handle counterclockwise. When the drill bit enters the turning state, water is injected for cooling. To prevent the drill bit from burning blue.
After drilling through, stop water injection, quickly turn the handle clockwise, move the spindle to the final stop, and turn off the motor. Lift up the clamping tool's pressure handle, detach the entire machine from the track, and complete the operation.
5. Repair and maintenance
The drilling machine must be protected from moisture when stored. If it is not used for a long time, it should be sealed with oil and packed in a box for storage.
.The gear box must be filled with grease during use.
3. Keep the drill bit sharp (edge angle) when drilling to ensure the normal operation of the drilling machine.
.The drilling machine should be wiped clean after use, and the places where oil needs to be filled should be filled with oil to prevent rust, and then stored in the warehouse.
.Check the machine grease once a year. If it is found to be missing or contaminated, grease should be added or replaced. The grease should be calcium-sodium based grease.
6. Precautions for safe operation
:
Check the rail clamping situation: According to the rail type, adjust the top screw of the clamping rail part. If it is too loose, the clamping is not secure. If it is too tight, , it is easy to damage the clamp head.
, Check the spindle drilling. The drill is withdrawn without jamming.
Check the screw connection between the motor and the frame.
. The motor must be idling for half a minute before operation, and the operation can be carried out only after the operation is stable and there are no abnormal phenomena.
When drilling, use even force and do not use too much force to prevent the drill bit from getting stuck.
. When drilling, be sure to prevent cooling water from splashing into the motor.
When drilling a hole, slow down the drilling speed to prevent damage to the drill bit.
After drilling is completed, the engine must be turned off and the machine must be unloaded. Do not touch the drill bit until it has completely stopped rotating.
The motor must be turned off when repairing, maintaining or replacing parts.
If any abnormality is found in the motor or gearbox, stop working immediately and do not disassemble it by yourself. Our company can send professionals to consider repair or replacement according to the specific situation.
Company introduction:
Jining Hengwang Industrial and Mining Machinery Co., Ltd. is located in the charming city of Jining, the hometown of Confucius and Mencius and the capital of canals. It borders the Oriental Holy City Qufu to the east, the historic Beijing-Hangzhou Grand Canal to the west, and the historic Beijing-Hangzhou Grand Canal to the south. Qilu is a beautiful Weishan Lake, with Mount Tai, the most famous of the five mountains, in the north. The company was established in 2001 with a registered capital of RMB 10,000 and currently has more than 100 employees. It specializes in operating rock drills, rock drills, shotcrete machines, support equipment, scraper accessories, rail equipment and other mining equipment and accessories according to market needs. The company adheres to the business philosophy of providing convenient services to customers, creating development opportunities for employees, and the entrepreneurial spirit of being enterprising and enjoying success. We warmly welcome new and old friends from all walks of life at home and abroad to negotiate trade, create great causes and create brilliance together.
Contact information:
Mobile:
Telephone:
Fax:
Manager: Zhang Shuang WeChat
:
Email: @
Website: :3
After-sales service and delivery instructions
, Cost-effectiveness instructions:
Under the same product quality conditions, our company will not reduce performance or change product parts at the expense of providing the lowest and most practical price s price. (Product production configuration can be carried out according to customer requirements)
Delivery instructions:
Delivery is based on the supply period. If there are special circumstances that require early delivery, our company will do so within a limited scope. We will organize personnel to increase productivity, implement production, installation, debugging, packaging and other processes, and strive to meet your company's requirements
Product delivery comes with instructions:
①Product manual and maintenance manual
②Product Certificate of conformity
③Instructions attached to purchased parts
④Wearing parts and their list (the source may vary depending on the model)
. After-sales service scope:
The product warranty period is one year. If the product has quality problems during the warranty period, our company will provide the fastest maintenance without any cost. If parts need to be replaced outside the warranty period, our company will only charge the cost
Track the product:
Our company will After the product is sold, there will be at least one technical return visit every month to track and record the use of the product so that any problems can be dealt with in a timely manner and strive to achieve customer satisfaction.