Deep plowing rotary tillage leveling integrated land preparation machine for reclaiming farmland and dam land rotary tillage machine large deep tillage machine

New
New. d
<# New> .> Deep plowing, rotary tillage, leveling, integrated land preparation machine, land reclamation, dam land rotary tillage machine, large deep tillage machine
<# New> .>
New . d一
d
d Product introduction:
New.
d Drive type with rotating cutter teeth as the working part
d Soil tillage machinery
d Also known as rotary cultivator. It has strong soil breaking ability and can make the soil finely crushed and mixed with fertilizers and evenly leveled in one operation to meet the requirements of dry land sowing or paddy field planting, which is beneficial to improve work efficiency during farming and make full use of the power of the tractor. However, the covering ability of stubble and weeds is poor, and the shallower plowing depth consumes more energy. Mainly used in rice fields and vegetable fields, it can also be used
New. . d
Rotary radius of rotary tiller:
. d
New. d Transmission mode: intermediate gear transmission
New. d cultivation depth:
New. d is mainly composed of transmission shaft, suspension frame, frame, gear box and other components.
New.
New.
New. d Three Machine Uses
d Instructions
New. d. At the beginning of the operation, the rotary tiller should be in the elevated state, first combine with the power output shaft to increase the cutter shaft speed to the rated speed, and then lower the rotary tiller so that the blades gradually penetrate into the soil to the required depth. It is strictly prohibited to combine the power output shaft or sharply lower the rotary tiller after the blade is inserted into the soil to avoid bending or breaking the blade and increasing the load on the tractor.
New. d. During operation, the machine should move at a slow speed as much as possible. This can not only ensure the quality of the operation, break the soil into fine pieces, but also reduce the wear of the machine parts. Pay attention to whether there is any noise or metal knocking sound from the rotary tiller and observe the soil breaking and plowing depth. If there is any abnormality, the machine should be stopped immediately for inspection and elimination before continuing the operation.
New. d. It is forbidden to work when the field is turning. The rotary tiller should be raised to keep the blades off the ground and the tractor's throttle should be reduced to avoid damaging the blades. When lifting the rotary tiller, the inclination angle of the universal joint should be smaller than the tilt angle. If it is too large, it will produce impact noise and cause premature wear or damage.
New. d. When reversing, crossing field ridges and transferring plots, the rotary tiller should be raised to the highest position and the power cut off to avoid damaging the machine parts. If moving to a distant location, use a locking device to secure the rotary tiller.
New. d. The rotary tiller should be maintained after each shift. Remove dirt and weeds from the blade, check the tightness of each connection, add lubricating oil to each lubricating oil point, and add butter to the universal joint to prevent increased wear.
New.
New. d Four mechanical adjustments
d Description
New. d. Left and right horizontal adjustment. Stop the tractor with the rotary tiller on flat ground and lower the rotary tiller so that the blade is 1 cm away from the ground. Observe whether the left and right blade tips are at the same height from the ground to ensure that the blade shaft is level and the plowing depth is uniform during operation.
New.
New. d. Front and rear level adjustment. When lowering the rotary tiller to the required plowing depth, observe whether the angle between the universal joint and the first axis of the rotary tiller is close to the horizontal position. If the angle of the universal joint is too large, the upper pull rod can be adjusted to keep the rotary tiller in a horizontal position.
New. d. Lift height adjustment. During rotary tillage operations, the angle between the universal joints cannot be greater than 10 degrees, and it cannot be greater than 10 degrees when turning at the head of the field. Therefore, when lifting the rotary cultivator, special attention must be paid to the use of the available screws for position adjustment. Tighten the limit of the handle at the appropriate position and use the height adjustment. If the rotary cultivator needs to be raised again, the power of the universal joint must be removed.
New. Our company mainly produces and sells: feed pellet machine, straw crusher, haymaker, walking tractor, multi-functional wheat seeder, corn seeder, large rotary tiller, turning plow, wood chip pellet machine, pit digger, corn thresher, peanut harvester Baling machines and other equipment
New d: Special note: The buyer shall bear all the round-trip freight for non-capital issues of the machinery sold by the company
New company name:
Qufu City, Shandong Province
Shuangying
Machinery Company
New contact person
Sun
Manager
New contact number:
New business
New company address: Shandong Province Yanshi Industrial Park, Yaocun, Qufu City
New. d Our company adheres to the business philosophy of *quality first, reputation first* to serve the majority of consumers and sincerely welcomes merchants to call us to discuss cooperation!
d