Yangjiang wet and dry lawn mower, stacking machine, Huangzhu grass mower

The silage mowing machine, lawn mower, and grass cutter produced and sold by Guangzhou Huaxing Machinery is used to chop various green hay, cereal straw, straw, wild grass, wheat straw, corn straw and other forages. It is an economical mowing equipment currently widely used. It has a large volume. It has the advantages of small weight, easy installation, operation and maintenance, and high production efficiency. The production is used to feed cattle, horses, sheep, pigs and other livestock forage and retting straw is returned to the fields. The main purpose is to cut the pasture into small pieces of 1cm to feed cattle, sheep, geese and fish or to make silage feed. The mower is mainly composed of the body, the grass feed roller, the blade holder assembly, the blade feeding device, the frame and other parts. Welcome to our company to purchase new mower equipment. Large-scale haymakers are in stock for one hour, tons and tons for a long time
One purpose of use and its performance characteristics
Professional haymakers are used to cut paddy straw, wild grass, wheat straw, corn straw, and various fodders for feeding It is used for cattle
horses, sheep, pigs and other livestock forage and retting straw for returning to fields.
The length of this machine can be adjusted to cut grass of two lengths by changing the position of the V-belt in the cone groove.
According to the user's needs, the cone wheels of different specifications can be used to cut grass of various lengths (the cone wheels are customized with the factory).
The feeding speed change mechanism of this machine adopts a combination of gear transmission and belt transmission, and all transmission parts
are equipped with high-quality rolling bearings. It has the characteristics of low noise and long service life.
The fixed-knife movable knife adopts a straight edge for easy adjustment and sharpening.
Two main technical performance parameters
Production efficiency kg/h
Supporting power kilowatts (horsepower)
Power supply voltage volts
RPM/min
Overall dimensions **
Length of guillotine: 2 knives mm mm 3 knives mm mm
Material throwing distance m
Machine weight kilograms
Three structure introduction
The machine is composed of the following mechanisms Composition (see Figure 1)
The feed inlet mechanism is mainly composed of upper and lower feed roller parts.
The rotary grass cutting mechanism is mainly composed of the moving knife body part of the fixed knife.
Feeding speed change mechanism, active cone pulley, passive cone pulley, V-belt transmission gear.
Grass cutting transmission mechanism motor wheel main shaft wheel V-belt.
Safety protection device Feeding protective cover (feed port) Transmission protective cover Variable speed protective cover Upper protective cover Lower protective cover Discharge port.
Sharpening and adjustment of the four-moving fixed knife
When the machine leaves the factory, the moving fixed knife has a sharp blade gap and has been adjusted. However, during long-term use, some grass or hay will appear and the efficiency will be significantly reduced, indicating that the blade If it is not sharp, it needs to be removed and sharpened.
Open the upper protective cover, loosen the fixing screw of the fixed blade, take out the blade, and sharpen the bevel edge of the blade with a grinding wheel or whetstone (see Figure 2).
Steps to install the fixed knife
) First, fix the fixed knife on the fixed knife holder with the fixed knife screw.
) Fix the movable knife to the movable knife body with the movable knife bolt and adjust the gap between the movable and fixed knife at the same time. Adjust the general gap to a suitable range as needed, tighten the movable knife bolt, and fix the jack screw and jack screw nut. tight.
If the V-belt is worn and slips and cannot enter the grass, the V-belt should be replaced in time.
When disassembling gears and angle pulleys for maintenance, attention should be paid to the direction of the thread rotation. The direction of thread rotation is as follows (refer to Figure 1). The driving cone wheel is left-handed and the passive cone wheel is right-handed. The bridge gear shaft is left-handed. The upper roller gear is right-handed and the lower roller gear is left-handed.
If machine parts need to be replaced due to non-human factors due to product quality, the company will not only replace them free of charge but also bear the cost of packaging and transportation of the parts. (Safety and credibility are guaranteed. You only need to pay a small deposit in advance and the balance will be paid after the goods arrive