Multifunctional hay kneading grinder feed grinder

Guangzhou Huaxing Machinery guillotine grinder, guillotine, beater and grinder in one, the latest development and production of small livestock feed processing machinery, the machine consists of guillotine, hammer, fan blades, three parts, combined into one, with crushing, guillotine This machine has three functions: grass grinding and grinding. This machine is specially designed for self-employed people. It is equipped with small power and single phase. This machine is mainly used for crushing, beating and guillotine raising cattle, sheep, pigs, rabbits, deer, chickens, ducks and geese. Grass, crushed. The above four functions can be achieved by changing the screen at will. The screen can be removed when cutting grass. When crushing, no screen or a screen with millimeter holes can be used. When beating, millimeters can be used. mm, mm holes of the screen. The main machine and the motor pulley adopt pagoda wheel speed change. When grinding, the main wheel uses millimeters, and when crushing and beating, the main wheel uses millimeters. Local distribution power specification voltage, watts. Speed per minute
Output in kilograms per hour
3. Technical Parameters
Type
Spindle speed
Rotor diameter
Standard screen (adjustable) supporting power Single-phase two-stage
Machine weight in kilograms
Appearance dimensions
Compared with the hay cutter, the hay cutter is an integrated machine that can cut grass and crush it. The machine can cut and crush corn stalks, rice straw, wheat straw, peanut soil, bean stalks, sorghum stalks, reed grass and other crop straws in one go. The finished materials produced by this straw crusher can be controlled according to the machine mesh. The size of the machine can be adjusted by changing the screen. It is an excellent machine and equipment for raising small poultry in rural areas.
The structure of the guillotine crusher is different from other hammer-type straw crushers. It is mainly composed of a feeding roller mechanism, a guillotine cutting mechanism, a gear transmission mechanism, a rotating shaft, a crushing device, an induced draft fan device, etc. The smallest model It can be driven by a household electric appliance, and there are wheels underneath, making mobile production very convenient.
This equipment seems complex but is actually very simple. It is equivalent to a silage machine and a hammer crusher mixed together. It has two feeding ports. Materials such as corn stalks and reed grass enter through the silage port. First, proceed Cut off the silage, and then the material enters the crushing chamber from the crushing port for secondary crushing. The finished materials that meet the requirements will leak out from the sieve holes and be drawn out by the induced draft fan to complete the silage crushing of the materials. Small materials (such as peanut shells, corn, etc.) The mandrel, soybean straw, etc.) will directly enter the crushing cavity from the crushing port, and then the material will be crushed, and the induced draft fan will pull out the material to complete the crushing. This kind of silage cutter is equivalent to a silage cutter and a hammer crusher. One can be used as two units, and the price is also cheap! Basic operation: When feeding, remove hard objects such as wooden sticks, ironware, stones, etc. from the material. According to the length of the material you need, install and adjust the gear, turn on the power source, and let the machine idle for a few minutes. If there is no abnormality, feed the material evenly. Too much will easily cause overloading and stalling, while too little will affect efficiency and stop working. You should stop feeding first, then let the machine idle for two minutes, blow out dust and weeds, and then shut down. Note: This machine has three gears. During normal use, push the handle to the forward position. When the material is blocked due to excessive feeding, immediately push the handle to the stop position, wait for a moment, and then push the handle to the retreat position until the material exits. Finally, reduce the feeding amount and resume work. When stopping work, adjust the handle to the stop position. When pushing the handle, it should be in place at once. During work, stand strictly on the feeding table and extend your hands to the upper and lower feeding rollers and pressure rollers. It is strictly forbidden to use wooden or metal rods to push materials into the feeding roller to ensure personal safety. No one is allowed to stand in front of the discharge port to prevent accidents. If the feeding port is blocked during operation, the handle should be removed immediately. Push to the stop position, pause for a few seconds and then push to the retreat position. If the problem still cannot be solved, stop the machine for inspection