Lanxi softened water equipment/chemical fiber boiler softened water treatment equipment

产地：

苏州

RO膜：

4040

材质：

玻璃钢

Lanxi softened water equipment/chemical fiber boiler softened water treatment equipment
Contact number Ms. Zhao:
Softened water treatment equipment, softened water equipment
-.
-..Softened water treatment equipment, softened water As the name suggests, the equipment is a device that reduces water hardness. It mainly removes calcium and magnesium ions in the water. In layman's terms, it is a device that reduces the hardness of water. Its main functions are to remove calcium and magnesium ions in the water, activate water quality, sterilize, kill algae, prevent and remove scale. Water softening equipment cannot reduce the total salt content in the water during the process of softening water. It is widely used in hot water boiler systems, heat exchange systems, industrial cooling systems, central air conditioning systems and other water equipment systems.
-.
-.
-:..: Working principle: Since the hardness of water is mainly formed and expressed by calcium and magnesium, cation
..ion exchange resin is generally used < (
-:..Water Softener
-..)
-:..Remove the water in the water
-..+
-:.
-..+(
-:..Main ingredient that forms scale
-..)
-:..Replaced with the resin
-..+
-:.
-..+
-:.. Increased resin removal
-..+
-:.
-..+
-:..'s effectiveness gradually decreases.
-.
-.
-:..When the resin absorbs a certain amount of calcium and magnesium ions, it must be regenerated. The regeneration process is to use salt in the salt box
-..table salt Water flushes the resin layer to replace the hardness ions on the resin and then discharges the regeneration waste liquid out of the tank, and the resin resumes its softening and exchange function.
-.
-.
-:..Because the hardness of water is mainly formed and expressed by calcium and magnesium. Because the hardness of water is mainly formed and expressed by calcium and magnesium, it indicates the sodium ion exchange softening process. The principle is to pass raw water through sodium-type cation exchange resin to make the hardness component in the water
-..+
-:.
-..+
-:..combined with the hardness component in the resin.
-..+
-:..Phase exchange to adsorb water
-..+
-:.
-..+
- :..Soften water.
-.
-.
-:..：Work flow: work
-..(
-:..Sometimes it is called the production of water
-..)
-:.Backwash, salt absorption
-..(
-:..Regeneration
-..)
-:.Slow Flushing
-..(
-:..Replacement
-..)
-:.Five quick flushing processes. All processes of different softened water equipment are very similar, but there may be some additional processes due to differences in actual processes or control needs. Any softened water equipment based on sodium ion exchange is developed on the basis of these five processes
-..(
-:.. Among them, fully automatic softened water equipment will increase the weight of salt water. Note process
-..)
-:...
-.
-.
-:..Backwash
-..:
-:..After working for a period of time, the equipment will intercept a lot of resin on the upper part Only after the dirt brought by the raw water is removed can the ion exchange resin be fully exposed and the regeneration effect can be guaranteed. The backwash process is that water washes in from the bottom of the resin and flows out from the top, so that the dirt intercepted at the top can be washed away. This process generally takes about
-.
-:..minutes.
-.
-.
-:..Salt absorption
-..(
-:..Regeneration
-..):
-:..The traditional equipment for injecting salt water into the resin tank uses a salt pump
-..The fully automatic equipment for injecting salt water into the resin tank uses a dedicated built-in ejector to inhale the salt water< (
-:..As long as the incoming water has a certain pressure
-..)
-:.. In the actual working process, the regeneration effect of salt water flowing through the resin at a slower speed is better than that of simply soaking the resin with salt water. Therefore, softened water equipment uses the method of salt water flowing through the resin at a slow speed to regenerate. This process generally requires
-.
-:The actual time of about ..minutes is affected by the amount of salt used.
-.
-.
-:..Slow Rinse
-..(
-:..Replacement
-..):
-:..After using brine to flow through the resin, use raw water to slowly rinse all the salts in the resin at the same flow rate. This process is called slow rinse because there is still a large amount of calcium and magnesium on the functional groups during this rinse process. Ions are exchanged by sodium ions. According to actual experience, this process is the main process of regeneration, so many people call this process replacement. This process generally takes the same time as the salt inhalation, which is about
-.
-:..minutes.
-.
-.
-:..Quick Rinse
-..:
-:..In order to completely rinse away the remaining salt, use practical methods Use raw water to flush the resin at a flow rate that is close to the work. The final water output of this process should be soft water that meets the standard. Generally, the quick flushing process is
-.
-:..minutes.
-.
tons of copies