CW6280A/B lathe manufacturer 6280A/B horizontal lathe hot sale

The complete motion process of the lathe manufacturer's horizontal lathe cutterhead is: the cutterhead is released, the cutterhead is clamped by turning left or right to the nearest designated tool position, and the cutterhead is clamped. Then the corresponding action sequence of the electromagnet is: power on (the cutterhead is released) (forward rotation) or (reverse rotation) power on (the cutterhead rotates) (for forward rotation) or (when reverse rotation) power off (the cutterhead stops rotating) Power off (cutterhead clamped). Lathe manufacturer's jet tube hydraulic servo system for horizontal lathes. The working principle of this servo system consists of a hydraulic cylinder, a receiving plate and a jet tube. The jet tube can swing to the left and right at a small angle around the axis perpendicular to the drawing surface. There are two side-by-side receiving holes on the receiving plate, and the pressure oil injected from the tapered nozzle at the end of the jet pipe is directed to the left and right chambers of the hydraulic cylinder respectively, causing it to move to the left or right. When the jet tube is in the middle symmetrical position of the two receiving holes, the pressure of the oil in the two receiving holes is equal. The hydraulic cylinder does not move. If an input signal acts on the jet tube to deflect it, for example, it deflects to the left at a small angle. The pressures in the two receiving holes are not equal. At this time, the pressure in the left chamber of the hydraulic cylinder will be greater than that in the right chamber. The hydraulic cylinder will move in the direction of deflection of the jet tube (to the left in this case) until the receiving plate that moves with the hydraulic cylinder arrives. until the jet hole is at a symmetrical position in the middle of the two holes.
<= d%> %> Specifications and models
%> >
%> Lathe lathe
%> Maximum rotation diameter on the bed
%> >
%> >
%> Lathe manufacturer Maximum rotation diameter on horizontal lathe tool holder
%> >
%> >
%> Maximum workpiece length
%> >
%> >
%> Rotary diameter/effective width in saddle groove
%> >
%> >/
%> Lathe manufacturer horizontal lathe spindle Through hole diameter and shaft head type
%> >
%> >(Series) (Series)
%> Spindle through hole front end taper and tip taper
%> >< br/> %> >(Series) (Series) Morse number
%> Spindle speed series and range
%> >r /
%> >Type-(Series)
%> />Type.-(Series)
%> Longitudinal feed level and range
%> >/
%> >Type
%> Range:
%> >/
%> >
%> Range:
%> >/
%> >
%> Micro feed range using exchange gear
%> >/
%> >
%> The ratio of transverse feed amount to longitudinal feed amount
%> >
%> >/
%> Saddle rapid traverse speed
%> >/
%> >
%> Machine tool screw pitch
%> >
%> >(metric)/(imperial) )
%> Number and range of metric thread types
%> >
%> >Types- (There are also non-standard threads)
%> Number and range of inch thread types< br/> %> >
%> >Species- .
%> Number and range of module thread types
%> >
%> >Species
%> Number and range of diameter pitch thread types
%> >
%> >Type-D
%> Maximum lateral travel of lower tool rest
%> >
%> >
%> Maximum stroke of upper tool rest
%> >
%> >
%> Tailstock sleeve stroke
%> >
%> >
%> Tailstock sleeve taper
%> >
%> >Mohs number
%> Lathe bed guide rail width and quenching hardness
%> >
%> >
%> Main motor power
%> >
%> >
%> Fast motor power
%> >
%> >
%> Cooling pump motor power
%> >
%> >
%> Machine width and height
/Packaging width and height
%> >< br/> %> >
/ /
%> Machine length/packing box length
%> >
%> >
%> Maximum workpiece length
%> >
%> >
%>
%> >
%> >
%>
%> >
%> >/
%>
%> >
%> >
%>
%> >
%> >/
%> < br/> %> >
%> >/
%>
%> >
%> >/
%> Machine tool net weight
%> >
%> >
%> Maximum workpiece length
%> >
%> >
%>
%> >
%> >
%>
%> >
%> >/
%>
%> >
%> >
%>
%> >
%> >/
%>
%> >
%> >/
%>
%> >
%> >/
%> Bed width
%> >
%> >
%> Maximum load-bearing
%> >
%> >< br/>