Flower basket tablet press price, industrial tablet supplier

Flower basket tablet press price, industrial tablet supplier

Structural features
(Flower basket tablet press price, industrial tablet supplier) )
This machine consists of series The three-phase asynchronous drive drives the main shaft to rotate through the triangle belt and the first-level cylindrical gear. The main shaft is equipped with three cam mechanisms. The border completes the three process procedures of filling, pressing and film discharging. Each procedure can be adjusted to meet the technical parameters. Require.

)Use and scope of application (
Flower basket tablet press price, industrial film supplier))
This machine is a medium-sized flower basket tablet press, suitable for Pharmaceutical, chemical, food, electronics, fuel and other industries press granular raw materials into tablet or block preparations.
This machine can press various round, ring-shaped and special-shaped tablets, as well as tablets with trademarks, text and simple graphics engraved on both sides.
This machine is not suitable for pressing semi-solid, wet powder and powder.
Technical parameters
Detailed parameters
Maximum tableting pressure in kN
Maximum tableting diameter
Maximum filling depth
Maximum outer diameter of annular tablets
Ring piece inner diameter
Ring piece depth
Production capacity pieces/minute
Motor power
Machine net weight in kilograms
Overall dimensions
) Installation and debugging

, Installation of the whole machine
The whole machine can be lifted by stringing a wire rope through the top, or it can be transported by a forklift. The whole machine should be leveled before it is put in place.

, Installation of power cord
The cable specifications are adapted to the motor power, voltage and current. The cable passes through the main switch and is connected with a flexible cable through a wire tube or socket plug. The cable passes through the outlet coil behind the machine base and enters the electrical box.
The steering of the motor should be consistent with the indication sign (that is, it rotates counterclockwise when viewed from the outer end of the upper pulley of the motor). The V-belt should be removed before correcting the steering, and the V-belt should be installed after correcting, and then pass the point. Press the movement button to confirm the correctness of the steering.

First, cut off the power supply on the machine, remove the hopper, feeder and middle mold platen, wipe the die holes of the middle mold platen, the upper and lower punch holes and the die, and then follow the following steps Steps are taken.
⑴ First insert the lower punch into the hole of the lower punch, insert it all the way to the root, and then align the screw with the gap in the fuselage
⑵ Insert the upper punch into the hole of the upper punch, and insert it all the way to the root. At the root, tighten the fastening screws
⑶Insert the middle mold into the hole of the middle mold table. Note that the end face of the middle mold must be lower than the plane of the table. Tighten the fastening screws on both sides.
⑷Install the middle mold platen onto the fuselage, insert it into the lower punch, and turn the large pulley to make the upper punch enter the middle mold hole. The gap should be even, flexible up and down, without interference and hard friction, and then tighten it. The fixing bolts between the middle mold platen and the fuselage
⑸Install the removed parts such as the feeder.

Adjustment of filling depth
Loosen the set screws on both sides of the filling adjustment nut. Lower the nut to increase the filling depth. After adjustment, the fastening screws must be tightened. Pay attention to the filling depth. Exceed.

Adjustment of tablet thickness
The eccentric sleeve on the eccentric shell connected to the upper punch is equipped with a scale, the value of which indicates the depth of the upper punch entering the middle mold. Before adjustment, first loosen the fastening bolts on the eccentric housing, and then drive the eccentric sleeve through the bevel gear to adjust the thickness of the sheet. After adjustment, the bolts and nuts must be tightened to prevent loosening.

, film discharge adjustment
Turn the pulley (clockwise) to raise the lower punch to the highest position, loosen the screws on both sides of the film discharge adjustment nut, rotate the film discharge adjustment nut, and make the lower punch Make the upper end face of the punch flush with the end face of the middle mold. After adjustment, tighten the screws on both sides.

Adjustment of the feeder
Turn the pulley to make the upper end surface of the lower punch rise to the highest level (level with the middle mold), adjust the flexible joint (the nut should be loosened before adjustment), so that the material can be added The front end surface of the feeder is close to the solid nut on the edge of the outer diameter of the lower punch, and then the pulley (must be rotated clockwise) is used to make the feeder move forward and backward several times and still meet the requirements.

The position adjustment of the downstroke lever directly affects the stability of the filling amount. Turn the pulley to lower the lower punch to the lowest position, that is, the filling adjustment nut is close to the fuselage. Adjust the upper and lower nuts so that the half-round head of the lower punch lever is close to the upper end surface of the filling adjustment nut, and tighten the upper and lower nuts.