10 years of professional quality spray iron room cooling project

Factory cooling project, iron sheet room cooling equipment
Factory ventilation cooling spray equipment
Iron sheet factory cooling
Iron sheet factory, the largest spray cooling system and cooling spray equipment manufacturer in China,

Factory cooling equipment, factory spray cooling equipment, factory cooling system


In the hot summer, it brings inconvenience to many steel frame structure factory users. Because the temperature is very high in summer, and the iron sheet on the roof is exposed to the sun for a long time, the temperature inside the factory can reach above 10 degrees Celsius. Many employees often suffer from heat stroke, dizziness, and fever due to the stuffy air and high temperature, plus working in high-temperature factories for a long time. This not only brings harm to the employees' health, but also seriously affects the factory's performance. Production efficiency. Therefore, cooling down the factory is a key issue that bosses need to consider in summer.
Most of today's industrial plants are made of colored steel plates. Due to the thermal radiation of the sun in summer and the heat generated by the operation of equipment in the factory, the ambient temperature reaches above ℃, causing discomfort to workers and causing nausea, dizziness, and heat stroke. wait. Production efficiency and production quality have also been reduced, and improving the working environment is an issue that cannot be ignored.
Working in a tin factory building in summer is a very painful thing, because the temperature inside the tin room is too high and the air is not circulating, making the room very stuffy. Many employees are unwilling to work in the summer, or simply leave the country, which results in low work efficiency, inability to recruit personnel, and declining efficiency in corporate units. Nowadays, when it comes to employing people in enterprises, it is not only about remuneration, but the working environment is also very important. Nowadays, part-time workers are more picky. If there is the same remuneration but a better environment, they will leave immediately, so it is very important to retain people. big event.
Shenzhen Yilu Technology Co., Ltd. independently developed and produced a special spray cooling system for high-temperature factory workshops and iron sheets. The electrical control is equipped with timing control. The spray time interval can be set arbitrarily through the host panel or through sensor signals. The computer controller of the conveyor host controls the constant voltage system with the frequency converter, which can control multiple operating environments in a timely manner according to the changes in internal temperature and humidity of the environment. No manual attendance is required, and automatic control is fully realized. The system equipment is easy to install. The pipelines are made of high-pressure copper pipes or nylon pipes. You only need to arrange the pipelines in the working environment. The required water source is clean tap water, which is non-toxic and harmless and has no impact on the environment. This efficient, energy-saving and convenient cooling equipment will surely become the new favorite in the market! Shenzhen Yilu Technology Co., Ltd. adheres to the business philosophy of customer first and enterprising, adheres to the principle of customers first, and provides high-quality services to our customers with integrity.

Today's industrial plants, stadiums, exhibition centers, factory sheds, and some large buildings are all made of colored steel plates or fiberglass structures. Due to the heat radiation of the sun in summer, the colored steel plates or glass sheds generate high-energy heat, causing environmental damage. When the temperature reaches ℃ or above, it will bring discomfort and irritability to people. In severe cases, it can also cause nausea, dizziness, heat stroke and other phenomena.
The spray cooling system is a new type of high-efficiency and energy-saving cooling equipment. It uses water as raw material and uses a high-pressure plunger pump to pressurize the water to above MPa. The cooling terminal sprays small-sized water mist particles from a special nozzle. It diffuses rapidly in the air. During the diffusion process, it is continuously evaporated and absorbs a large amount of heat energy. The ambient temperature instantly drops by ℃~℃, giving people a more comfortable working environment.
After the entire mist cooling system is started, only electricity is needed to atomize water and the energy consumption is very low. From the perspective of cost performance and cooling effect, this system already has considerable advantages.

The roof glass shed factory cooling product system produced by Shenzhen Yilu Technology Co., Ltd. is equipped with timing control in the electrical control. The spray time interval can be set arbitrarily through the host panel and can also be transmitted through sensor signals. The host computer controller uses a frequency converter to control the constant voltage system, which can control multiple operating environments in a timely manner according to the changes in internal temperature and humidity of the environment. It does not require manual supervision and fully realizes automatic control.

The system equipment is easy to install. The pipelines are made of high-pressure copper pipes or nylon pipes. You only need to arrange the pipelines in the working environment. The required water source is clean tap water, which is non-toxic and harmless and has no impact on the environment. This efficient, energy-saving and convenient cooling equipment has slowly become the new favorite in the market!
"Cooling the roof glass shed factory building" requires that the fog particles should be relatively small. Microns are appropriate. The spray produces negative ions. Its chemical reaction formula is ++. That is: water light ions + hydroxide ions. Water is an extremely weak electrolyte that can ionize weakly. After ionization, water changes into hydroxide ions, which are negative ions.
"Rooftop Glass Shed Factory Cooling" There are two major types of nozzles. The conventional ones are centrifugal nozzles. A piece of super-hard special alloy is drilled with a laser, and a stainless steel precision small piston is installed behind the small hole. Driven by the high-pressure water flow, the small piston moves at high speed, tearing the water into extremely fine droplets, which are sprayed out through the small holes into mist. This type of nozzle has a wide range of applications. The other is an impact nozzle, where the high-speed water hits an extremely fine needle tip and breaks into mist. Due to the large amount of fog, this type of nozzle is most suitable for creating artificial fog landscapes
With the coming of summer, the hot and high temperatures will test people's endurance, and air conditioners will be in hot demand. However, the annual power shortage and blackouts are frustrating. In particular, the cooling of factories consumes huge amounts of electricity. With the government encouraging energy conservation and consumption reduction, special spray cooling systems for high-temperature factory workshops made of iron sheets have become a new favorite in the market.
Most of today’s industrial plants are made of colored steel plates. Due to the thermal radiation of the sun in summer and the heat generated by the operation of equipment in the factory, the ambient temperature reaches above ℃, causing discomfort to workers and causing nausea, dizziness, and heat stroke. wait. Production efficiency and production quality have also been reduced, and improving the working environment is an issue that cannot be ignored.
The area of a factory building is generally several thousand or even tens of thousands of square meters, and the cooling capacity of ordinary fluorine air conditioners cannot satisfy such a huge operating area. The initial equipment investment and later operating costs of choosing a central air-conditioning system are huge and unrealistic, especially in the summer when there is a large power shortage and power cuts are a common trend. It is in such a situation that the spray cooling system has huge market potential .
As the global temperature rises, in summer, the outdoor temperature is high, coupled with the operation of many factory machinery and equipment, the indoor temperature can reach above 10 degrees, causing serious discomfort to the workers. Exaggeration It can also cause nausea, dizziness, heatstroke and other phenomena. Production efficiency and production quality are also reduced, so improving the working environment is a big issue that cannot be ignored. But while improving the environment, the investment cost must also be considered. The cost of using air conditioning is too high. The later cost of water curtains and fans is also high and the cooling range is small. After comparison, using a spray cooling system to cool down is the most ideal and cost-effective. The spray cooling system has good cooling effect and low operating cost.

Today's industrial plants, stadiums, convention and exhibition centers, and some large buildings are all made of colored steel plates or fiberglass structures. Due to the thermal radiation of sunlight in summer, the colored steel plates or glass sheds generate high-energy heat, causing the ambient temperature to reach Above ℃, it will bring discomfort and irritability to people. In severe cases, it may cause nausea, dizziness, heatstroke and other phenomena.
In hot and dry summers, employees working in the workshop are prone to heat stroke, which seriously affects their health and reduces work efficiency.
The average summer temperature is above 10 degrees, and the temperature in the workshop is even higher. If you stay in a place with a temperature higher than the normal range for a long time, you are prone to heatstroke.
Traditional workshop cooling method. Industrial fan cooling cannot fundamentally reduce the ambient temperature to meet usage needs.
Although air conditioning cooling is effective, the equipment investment cost is huge and the operating cost is high. It is usually used for indoor cooling.
The air is dry and the air humidity in the workshop is too low. Due to the low humidity in the equipment functions and processing technology, the production process requirements cannot be met, resulting in serious losses.
High temperature, dryness, and low humidity will cause the product to dry out, crack, and deform, generate static electricity, and shorten the service life of the equipment.
Industrial humidifiers have limited humidification area, large investment, and high equipment operating costs
With the introduction of spray cooling technology at the Shanghai World Expo in 2016, it has slowly entered the public eye, with its energy saving, environmental protection, cooling, moisturizing, etc. The characteristics are recognized and promoted by more and more enterprises and institutions.

Shenzhen Yilu Technology Co., Ltd. spray system solution!
Adopting Yilu Technology’s high-pressure spray system, it can produce mist droplets as fine as microns, making full use of the latent heat of vaporization of water vapor to quickly and efficiently take away a large amount of heat, reduce the ambient air temperature, and keep your factory building at a certain temperature. A higher working environment will also increase the air humidity, making people feel more refreshed.
For many textile factories, steel mills, chemical fiber factories, printing factories, painting factories, cigarette factories and other production environments, humidification and cooling face many problems. Baker spray can change direct atomization from liquid water to gaseous state. It increases the air humidity and reduces the air temperature. It can also eliminate static electricity in textile factory workshops.
The best choice for workshop cooling and humidification!


Advantages of spray cooling system:

Fine mist: The average mist droplet diameter is microns, and the mist will not wet clothes.
Good atomization effect: the mist is completely atomized after leaving the nozzle centimeters, and there will be no accumulation of water when encountering obstacles.
Purify the air: increase the negative ion content in the air, accelerate the air flow, and make the air feel cooler.
Energy saving: The water consumption of each nozzle is calculated in milliliters/minute.
Hygiene: The water in the high-pressure micro-mist system is sealed and non-circulated, which will not cause the growth of bacteria.


Cooling effect: The water mist absorbs a large amount of heat during the vaporization process, thereby achieving rapid cooling and effectively reducing the surrounding environment.
[Operating costs] (Example: Flat factory building)
Based on the host running minute-stop cycle, calculated based on standard working hours (hours):
, daily water consumption for sprinkler heads *./ (per Each nozzle sprays water per hour (liters per hour) * (time the host runs every day).
, Daily electricity consumption. (motor power) *...
, one day operating cost.ton*yuan (price per ton of water) +.*yuan (electricity fee per kilowatt hour).yuan.
[Investment Cost] (Example: flat factory building)
The spray system (host, electronic control system, filtration system, high-pressure pipeline) can be selected according to customer requirements. The total system price is about 0.000,< br/>



The spray cooling equipment produced by Shenzhen Yilu Technology Co., Ltd. is equipped with timing control on the electrical control, and the spray time can be set arbitrarily through the host panel. The interval can also be transmitted to the host computer controller through sensing signals, and the constant voltage system is controlled by the frequency converter. Multiple operating environments can be controlled in a timely manner according to changes in internal temperature and humidity of the environment. No manual attendance is required, and automatic control is fully realized.

How to cool down the factory building, how to cool down the factory building, cooling down the factory building and workshop, methods of cooling down, workshop cooling down, the price of workshop cooling down, the cost of workshop cooling down, cooling down the workshop and factory building together. Regardless of whether your factory is in a high temperature of ℃ to ℃, or has a lot of dust, moisture, or poor ventilation, it is very stuffy. We all have reasonable solutions that can keep your company's factory buildings between ℃ and ℃ and create a natural and comfortable working environment, so that your company can produce efficient, energy-saving, environmentally friendly effects and improve work efficiency. Spray cooling system: cooling of squares, spraying of leisure and entertainment squares, cooling of coffee shops and BR bus stations, cooling and dust removal of roads, cooling and moisturizing of park scenic spots. In sultry weather, tourists who go to the square area must be very hot and irritable. In order to improve this environment, Shenzhen Hanbo Environmental Protection Company has launched a spray cooling system, which allows tourists to feel the coolness in the air while playing, thereby improving the mood of the tourists. , a long and slender pipe, floating out fine water mist. A burst of coolness hits your face, but it doesn't make your body wet. The spray cooling system will greatly improve the mood of tourists in hot weather. r Factory workshop cooling equipment water mist cooling. The working principle of the spray system is to pressurize tap water through a booster pump to produce mist particles with a diameter of microns from the nozzle. The mist particles disperse in the air and take away the surrounding heat when they evaporate. , can have a cooling effect. The factory workshop system consists of a host machine, nozzles, water treatment systems and pipelines. The working principle is: after the water is purified, it is atomized through high-pressure impact. When the water particles change from liquid to gaseous state, a large amount of heat in the air will be taken away. , which has the effects of purifying the air, removing dust, cooling and moisturizing. If it is operated hourly a day, it only needs one liter of tap water and only one watt of electricity, which is equivalent to the energy consumption of an air conditioner. With the arrival of summer, the temperature gradually rises and the cooling effect will be more obvious.

Working in a tin factory building in summer is a very painful thing, because the temperature inside the tin room is too high and the air is not circulating, making the room very stuffy. Many employees are unwilling to work in the summer, or simply leave the country, which results in low work efficiency, inability to recruit personnel, and declining efficiency in corporate units. Nowadays, when it comes to employing people in enterprises, it is not only about remuneration, but the working environment is also very important. Nowadays, part-time workers are more picky. If there is the same remuneration but a better environment, they will leave immediately, so it is very important to retain people. big event.
To retain people, we must first provide employees with a comfortable working environment. So what constitutes a comfortable environment? To put it simply, it is necessary to cool down the factory. There are many ways to cool down, including air conditioners, water curtains, environmentally friendly air conditioners, fans, and the spray cooling system I want to recommend today.
The spray cooling system is a magical thing. It only needs to spray for about a minute to immediately cool down the room. It also has the characteristics of low cost, good cooling, and low maintenance. Some people say why not use other ones? Let’s briefly summarize other cooling methods. Air conditioners are not realistic, water curtains are not comprehensive, environmentally friendly air conditioners do not save electricity, and fans are only a means of ventilation. Next, let’s introduce the spray cooling system in detail.
Uses
, cooling: outdoor restaurants, entertainment venues, stadiums, sports fields, airports, bus stations, large gatherings, hotels, livestock farms, pigs, horses, cattle and sheep, cooling
, dust removal: removing air dust particles, mainly used in farms and mines etc. to control pollution
, humidification: used in textile factories, cotton wool warehouses, parks, greenhouses, laboratories, flour processing plants, etc. to increase air humidity
, agriculture: used in family farms, mushroom cultivation fields, circus arenas, aviaries, kennels and feeding The farm makes the environment suitable for the growth of various poultry
, industry: metalworking workshop, machinery workshop, textile workshop, clothing workshop, printing and dyeing, shoemaking, plastic injection molding, heat treatment, casting glass products, spray electroplating, electronic chemical industry, metallurgy, leather, toy manufacturing, home appliance manufacturing, etc. It is also used for cooling and dust removal. Can be used to eliminate static interference
, special use places: gardens, zoos, shopping malls, exhibitions, movie theaters, flower and tree breeding, animal husbandry, mushroom houses, etc. for humidification and cooling, can also be used for plant irrigation
, special use method: in water Join