stainless steel food pump

When installing the suction pipeline, the installation height of the suction inlet should not exceed 1 meter. When conditions permit, the installation height of the suction inlet should be as low as possible below the lowest water storage level of the pool, and the length of the suction pipe should be as short as possible. , install fewer elbows, which will help shorten the self-priming time and improve the self-priming function. Valves, flanges, etc. in the suction pipeline should be strictly prevented from leaking air or liquid, that is, no air leakage is allowed in the suction pipeline. Solids and other impurities should be prevented from being sucked into the pump body, and a filter should be installed on the suction pipeline. The effective flow area of the filter should be times the cross-section of the suction pipe, and the filter should be inspected regularly. The suction pipeline and discharge pipeline should have their own brackets, and the pump body itself is not allowed to bear the load of the pipeline. . When installing the pump, the electrostatic grounding resistance of the pump and pipelines should meet the specified requirements. . During installation, you should strictly check whether there are stones, iron sand and other debris in the pump casing and pipelines. . Correct the installation clearance and coaxiality of the pump coupling and motor coupling. The allowable deviation of the non-axiality is meters. The height difference between the pump shaft and the motor shaft can be adjusted by placing copper or iron sheets on the feet. 2. The corrosion-resistant self-priming pump should be inspected after the actual operation of the unit for several hours. If there are no adverse phenomena, the installation is considered to be proper. The temperature of the bearing should be checked during the trial operation. The temperature of the bearing body should not exceed ℃. . The cooling water joint of the bearing body of this pump equipped with a cooling chamber device is used for a rubber hose or plastic pipe with an inner hole of . Its thread size is . . If a one-way valve is installed on the outlet pipeline of the pump and the pump cannot discharge gas smoothly during the self-priming process, a small exhaust pipe and valve should be added to the outlet of the pump.
Use of pump
(1) Preparation and inspection before starting the corrosion-resistant self-priming pump. The self-priming pump is lubricated with high-quality calcium-based butter and No. 1 engine oil according to the working conditions of the pump. If the pump is lubricated with butter, butter should be added to the bearing box regularly. If the oil level of the pump lubricated with engine oil is insufficient, add enough. , check whether the liquid storage in the pump casing is higher than the upper edge of the impeller. If it is not enough to inject the liquid directly into the pump body from the liquid filling port on the pump casing, the operation should not be started when the liquid storage is insufficient, otherwise the pump cannot It works normally and the mechanical seal is easily damaged. , check whether the rotating parts of the corrosion-resistant self-priming pump are stuck in magnetic collisions. Check whether the nuts at the bottom of the pump body and the joints are loose. Check the coaxiality and parallelism between the pump shaft and the motor main shaft. Check whether there is air leakage in the inlet pipeline. If there is air leakage, try to eliminate it. Open the suction line valve and open (do not fully open) the outlet control valve.

Corrosion-resistant self-priming pump Disassembly and assembly sequence: Remove the motor or disengage the coupling. Remove the bearing body assembly, check the radial clearance between the impeller and the front ring, and check whether the impeller nut is loose. Remove the impeller nut, pull out the impeller, and check the radial clearance between the impeller and the rear sealing ring. Loosen the set screw of the mechanical seal, pull out the moving ring part of the mechanical seal, check the fit of the end faces of the moving and stationary rings, and check the sealing condition of the sealing ring (or buffer pad). Unscrew the coupling nut and pull out the coupling. Remove the bearing end cover and remove the pump shaft and bearings. When installing the corrosion-resistant self-priming pump, assemble it in the reverse order.
Vertical multi-stage centrifugal pump/
The original text is reproduced from Asia Fluid Network. Please indicate the source for reprinting.