Year1
- 线体大梁：
- 1.5厚方通
- 箱体外壳：
- 1.5㎜厚冷板
- 机架：
- 50×50㎜方通
Shenzhen Tunnel Oven|Infrared Tunnel Furnace Parameters The following examples are for reference only
Shenzhen Tunnel Oven|Infrared Tunnel Furnace Partial Dimensions Line Body Total Length Meters, Tunnel Furnace Mesh Bandwidth Meters, Tunnel Furnace Total Height, Tunnel Furnace The discharging part is meters long, the drying part of the tunnel furnace is meters long, divided into sections, the feeding part is meters long, the line body beam adopts square tube, the tunnel furnace box shell is made of thick cold plate bending, the tunnel furnace shell has high temperature The non-ordinary electrostatically sprayed paint is corrosion-resistant and easy to clean. The tunnel furnace frame is welded with ㎜ square tubes and equipped with ㎜ adjustable foot cups. meters, the total length of the furnace cavity is made of thick galvanized sheet, the total height of the furnace cavity, the net height of the feed inlet, adjustable baffles, ㎜ thick high-temperature silicate insulation rock wool in the middle, and the bottom of the mesh belt is equipped with high-temperature insulation Thermosphere. The outer part of the tunnel furnace body is not hot to the touch. It is equipped with an exhaust valve, which can adjust the indoor air flow and make the temperature more uniform. The furnace lid can be independently flipped up and opened for cleaning inside the furnace
Zhen Tunnel Oven | Infrared Tunnel The power supply of the furnace electrical part is three-phase, three-phase and five-wire system. The tunnel furnace adopts Taiwan Adli frequency converter for frequency control and is equipped with a Taiwan Lixiang speed motor and an Oakley brand reduction gearbox. The speed ratio is Transmission gears and transmission chains, the transmission speed can be adjusted in meters/minute, equipped with an independent control system. Each section of the tunnel furnace is equipped with a Lixiang brand wind motor, equipped with an eight-and-a-half-inch wind wheel, and a built-in heating pipe in the furnace cover. In the air trough, the tunnel furnace has a total of air transport motors, each of which makes the temperature in the furnace more uniform. Each section of the tunnel furnace is equipped with infrared heating pipe strips, a total of 10 strips, each of which is evenly distributed inside the furnace cavity. The tunnel furnace transmits The bottom of the tunnel furnace is equipped with a heat insulation layer with a thickness of 0.0 to 100 ℃, so that the temperature outside the furnace is not too hot and the temperature is below 10 degrees. Each section of the tunnel furnace is equipped with an independent control electric box and temperature control system, so different temperatures can be set for the tunnel furnace
Infrared Tunnel In the furnace control part, each section of the furnace cover is equipped with a separate small control electric box. The temperature of each section can be independently controlled and displayed. The temperature control system is a Japanese microcomputer intelligent digital display thermostat, equipped with and digital display window. The tunnel furnace adopts The module's continuous buffer output controls the heater, and the tunnel furnace uses CHINT AC contactor output. The temperature control effect is more stable and the performance is more excellent. The tunnel furnace can automatically adjust the output power according to the temperature error to make the temperature more accurate. The temperature of the tunnel furnace can be adjusted from room temperature to ℃. The thermostat function has self-tuning calculus control automatically. Constant temperature, over-temperature, power-off alarm, leakage protection, motor overload protection and other functions. When the set temperature is reached, several sections of the heating tubes can be turned off at will to reduce the heating power, thereby achieving the power saving effect. Other control circuit electrical appliances of the tunnel furnace are controlled by Chint Electrical Appliances.
Zhen Tunnel Oven | Infrared Tunnel Furnace transmission part
Uses stainless steel mesh belt, equipped with a mesh belt support plate in the middle. The head and tail are equipped with an adjustable active roller to prevent the mesh belt from running away
Our company Mainly produces tunnel ovens. Tunnel ovens are mainly suitable for baking electronics, transformers, inductors, hardware, glass, rubber, silicone products, printing and other products. Compared with traditional ovens and hot air circulation ovens, the biggest advantage of our company's tunnel oven is that the inside and outside of the baked products are heated at the same time, the temperature difference between the inside and outside is small, no deformation, no discoloration, stable quality, fast baking speed, high efficiency, can save about 2 times the time, and shorten the time significantly. Local heating during the production and delivery cycle, less energy waste, saving electricity. The amount of energy transmission per unit area is large, so it is small in size, saves site space, saves construction costs and is connected to the production line. It can be controlled synchronously to reduce defects and can be controlled in sections. In order to meet the needs of the product, the high-flexibility exhaust device has little solvent residue and low risk. The outer temperature of the environmentally friendly shell is close to the ambient temperature, making the working environment comfortable and reducing energy waste. The product dissipates heat through the heat dissipation area and does not need to be left standing after baking, shortening working hours and reducing waste. The pollution-free constant temperature control system ensures stable product quality.
Shenzhen Tunnel Oven | Infrared tunnel oven is suitable for the surface spraying process of shells in computers, electronics, home appliances, audio, hardware, toys, crafts, crafts and other industries. Dust spraying is a closed production workshop composed of steel sandwich panels, which can effectively control defects. Air pollution to products, reducing dust in the spraying area and the defective rate of products. Dust-free spraying technology improves the appearance quality of products, such as the casings of TVs/computers, mobile phones,/, game consoles, video recorders, handheld computers, cameras, stereos, hair dryers, cosmetics, toys, etc. Manual dust removal in the process upper part area, electrostatic dust removal, manual spraying, drying area, paint curing area, cooling area, silk screen area, quality inspection area, receiving area, specifications and dimensions are designed based on process flow
Tunnel furnaces are distinguished by heating methods and have the following types
Full hot air continuous constant temperature drying
Far infrared heating continuous constant temperature drying
Hot air infrared combined type continuous constant temperature drying.
This type of Shenzhen tunnel oven | infrared tunnel oven has a wide range of applications and is suitable for occasions that require continuous drying and curing. There are many varieties. It is also suitable for SMD red glue curing relays epoxy glue curing magnetic materials and The dehydration and drying of hardware stamping parts after cleaning can be designed and manufactured according to customer requirements, and can be combined with other production lines to form a continuous tunnel furnace.
Shenzhen Chengxinxiang Technology Co., Ltd.
Business consultation Mr. Cai
Business consultation
Address Building, Baoshan Third Industrial Zone, Pingshan New District, Shenzhen
WhatsApp
