Sales of car awnings and outdoor awnings in Shatin, Dongguan

规格：

定制

In the process of building an awning, an indispensable step is to choose the most suitable materials. So, how to choose to save materials, trouble and money? Below we will make corresponding analysis based on various materials of the awning.
Forms of awnings
(
) Small awnings
Such as cantilevered awnings, hanging awnings
(
) Large awnings< br/> Such as wall or column supported awnings
According to the material, the awnings can also be divided into
,
Fiberglass structure awnings
,
Fiberglass structure awnings< br/> ,
All-steel structure awning
All-steel structure awning
,
Plate
(
Sunshine board, endurance board
)
Awning
Material characteristics of the awning
Detailed explanation of the advantages and characteristics of the endurance board as the roofing material of the solar panel awning
Flame retardancy
Autoignition temperature of the endurance board
℃ (wood is
℃ tested by the National Fireproof Building Materials Quality Supervision and Inspection Center,
The flammability of the board reaches
(
The flame retardant
level is classified as refractory Combustible engineering materials. Chemical corrosion resistance
Durable panels have good chemical corrosion resistance and can withstand various organic acids, inorganic acids, weak acids, vegetable oils, neutral salt solutions, aliphatic hydrocarbons and alcohol at room temperature. Erosion. Heat resistance and cold resistance
Durable panels have good temperature difference resistance, can adapt to various severe weather changes from severe cold to high temperature, and maintain various physical properties in the range of
℃ to
℃. Stable performance indicators. Photochemical properties
Durable panels have the highest light transmittance in the visible and near-infrared spectrum. Depending on the color, the light transmittance can reach

Tempered glass is ordinary glass that has been uniformly heated , when close to the softening point, it is uniformly cooled at a corresponding cooling rate according to different thicknesses. This generates strong permanent internal stress inside the glass, and the tensile stress of the inner layer and the compressive stress of the outer layer are in a stable stress balance state. Changed The original physical properties of glass overcome the original performance of glass and increase the scope of use
Tempered glass has high impact strength
(
Glass products processed by the tempering process are resistant to pressure Impact resistance is improved
times

High bending strength
(

times higher than ordinary flat glass

Thermal stability Good resistance and smooth
,
Transparent
,
Can be cut and other characteristics
When damaged by super strong impact
,
The fragments will be dispersed Small granular
,
No sharp edges
,
So it is also called safety glass
Laminated glass
(
That is, laminated glass
)
, laminated glass has very good safety. Due to the adhesive effect of the plastic lining in the middle, when the glass breaks, the fragments will not fly away, only radial cracks will occur, it is safe and does not hurt people, so it is widely used For car windshields. At the same time, the impact strength of laminated glass is much higher than that of ordinary glass, and it is not easily broken when impacted. In addition to the above properties, laminated glass also has a unique anti-theft effect. It is relatively safe because it is not easy to be broken into. There is another independent structural system in the curved arm telescopic awning. It has no rear pipes, no spray paint, and no spray patterns on the arms. Firm and focus on the iron plate brackets on both sides. If the length of the canopy exceeds
, the added arm in the middle is directly assembled and focused on the middle bracket. The iron plates on both sides are directly installed on the solid wall with expansion screws. Or firmly welded to an indirect iron frame. The installation conditions require protruding eaves or rain shields. The telescopic crank-arm awning is an awning that can be retracted and retracted at different extension lengths. The aluminum alloy bracket can withstand
/
wind speed. The maximum width can reach
meters, and the extended length can reach

meters. The adjustment is divided into manual, electric, remote control, wind control, light control, rain control and other methods for you to choose from. Features The main feature of this tent is that it is cheap and practical. Shade cloths are generally equipped with ordinary awning canvas, which is suitable for ordinary shops and small and medium-sized ordinary cities.
In general
Awning materials are currently the most common and practical awning materials.
Construction instructions for each process
Measurement and setting out
According to the design axis and elevation, measure the supporting steel beams (the longitudinal and transverse axes and elevations of each steel claw support member of the floor to meet the needs of the curtain wall Support structure and steel claw positioning requirements.
Structural reinforcement
The main structure of the awning uses the original civil structural steel beams as the supporting structure. It must also be reinforced according to the awning structure, adding tie rods, beams, etc.
Welding of stainless steel component skeleton
Start welding the awning skeleton. The main keel used in the glass awning skeleton is
stainless steel components. The selected models must comply with the structural calculation strength stipulated by the country. Welding must comply with According to the national standards, the weld must be continuous, with no leakage, no slag inclusion, and no unfusion defects. The welding height meets the design requirements. The stainless steel main keel is welded to the main structure through galvanized angle steel, and then tightened with stainless steel bolts The parts are fixed on the galvanized angle steel adapters on the left and right sides.
Installation of the connection base
Determine the installation position of the connection base according to the glass partition. When installing the connection base, electric welding should be used for spot welding positioning , after all the connector seats are spot welded and positioned, then pull the wires through for inspection, and adjust the connector seats that deviate from the positioning point.
Connector seats welding
After the connector seats are adjusted, weld them, using
Welding rod, diameter
, the periphery of the connection seat is fully welded, the welding height is in accordance with the design drawing requirements, and the welding quality is required to meet the following requirements
① The welding height meets the design requirements
② The welding seam is continuous , no leakage of welding or slag inclusion