Electric blast drying oven

Introduction to the electric blast drying oven Working temperature range Room temperature
Using voltage/temperature control accuracy Heating power Temperature uniformity ℃ blast power table Demand side commonly used temperature According to customer requirements Specifications Dimensions Studio size ** Depth * Width * The overall dimensions are about ** including the protruding part, depth*width*height. Box production materials. Overview of the structure of the machine. It adopts air outlet from both sides and return air circulation at the top. The heating element is installed in the side air duct of the oven. The circulation motor is installed on the top of the oven. To extend the life of the motor, the double doors and door buckles use spring handles. The electrical control panel is installed on the side of the box. Cabinet outer wall material: carbon steel cold-rolled plate, metal bending, welding and rivet splicing. Cabinet air plate material: stainless steel inner tank: carbon steel cold-rolled plate, metal bending and welding rivet splicing. Box air duct material: stainless steel inner tank: carbon steel cold-rolled plate Sheet metal bending, welding, rivet splicing, box frame material, angle steel, box reinforcement material, angle steel, partial use of plate bending, box bottom load-bearing frame material, angle steel, box bottom material, angle steel, box top frame material, angle steel, insulation layer thickness and material grade, high-density silicic acid The thickness of the aluminum fiber-filled insulation layer is
After the outer box coating material is rust-proofed, the surface is covered with environmentally friendly hammer paint. The color can be specified by the customer. Door production method. Door outer wall material. Cold-rolled steel plate. Sheet metal. Bending, welding and rivet splicing. The inner wall of the door. Material: cold-rolled steel plate, sheet metal, bending, welding, rivets, splicing door quantity, double door layer door thickness, door buckle, alloy hinge and tie rod, door frame sealing material, high temperature resistance, silicone rubber, ℃ pressure seal, good sealing performance, door opening method, left and right opening, studio configuration according to customer needs Car size
Width*depth air intake and exhaust apertures, integrated regulating valve. The exhaust hole diameter is 3, and the air output volume can be adjusted manually.
Blowing system blowing mode horizontal circulation wind motor device top wind wheel material alloy wind wheel wind wheel size * heating system heating element adopts jacketed far infrared heater type tubular electric heating generator, / piece, total assembly , total power of heating elements, grouped heating switches, continuous use life of more than 10,000 hours, number of heating elements, installation of heating element devices in the side air duct of the oven, heating time, instructions for each division test, the test point should be at least millimeters away from the inner wall material, the distance Door at least mm. The test time should be at least minutes after reaching the temperature constant state. Electrical appliance configuration control instrument intelligent digital display temperature controller, temperature control accuracy ℃, with adjustment, automatic constant temperature. When the device is set, a manual switch is required. When the temperature reaches the set temperature, the timing starts. When the time reaches the set range, the heating power is cut off. Intermittent alarm device/type sound and light alarm device, alarm prompt at the end of set time.
The control circuit voltage/temperature device is equipped with a stainless steel armored resistance temperature sensing device for accurate temperature measurement. Protection system leakage protection, circuit breaker protection, motor overload protection, grounding protection. The circuit breaker starts with leakage protection, effectively protecting all electrical components. The contactor output temperature control accuracy of the contactor is accurate using Chint brand electrical. The switches and other electrical components are made of CHINT brand electrical components and are not easily damaged. Product Attachment Description Product production cycle begins with the arrival of the advance payment on one working day/unit. The accompanying spare parts include an instruction manual, an instruction manual for electrical components, a warranty sheet, and a certificate of conformity. Warranty Scope: The entire product is guaranteed for one year, except for manual damage and natural disasters, including all electrical components. Quotation and payment method, freight and tax rate. The price includes tax stamps and freight. The delivery location is the designated location in Suzhou, excluding going upstairs. Payment method: Sign the contract and make advance payment. After the equipment production is completed and the test is completed, the payment must be paid before delivery. The buyer needs to cooperate with the forklift/driving truck for unloading the oven and installing it in place for hoisting work. We will provide civil engineering drawings to complete the basic civil engineering of the oven. The working power supply is connected to the air switch of the supplier's equipment control cabinet. Installation requirements: The front of the device must be no closer to the wall, and the left and right rear sides must be no closer than each other. The user must provide an independent power distribution switch and be responsible for connecting the power supply external to the equipment. Normal working environment conditions
Temperature ℃~℃, relative humidity not higher than the surroundings, no strong vibration and air flow, power supply, AC, no corrosive gases, please be sure to ground!
Thank you for your attention to our products and look forward to cooperating with you!