VALTEX

Qinhuangdao Dia Machinery distributes American Votex
Grease, cleaning fluid, sealing grease,
,
Sealing grease, -Sealing grease,
Votex sealing grease
Emergency lubricating oil sealant+
Sealing grease
Valve cleaning fluid
Grease gun
Grease
Foot-operated grease gun
Foot-operated hydraulic Grease gun
- Foot-operated sealing grease gun
Valve cleaning fluid
Grease gun
-
Sealing grease+
Hydraulic lubrication pump< br/> -Grease gun
-
Hydraulic lubrication pump
The grease is a special grease and cleaning fluid for Cameron valves, sealing grease, and the grease is a synthetic oil thickened by a complex soap It is refined with various additives such as anti-wear, anti-oxidation, and anti-rust. It is resistant to organic acids, alkali solutions, and chemicals. It has excellent resistance to water and petroleum products (such as gasoline, aviation oil, lubricants and mixed oils). It is widely used in wellheads and transmission pipelines. Low temperature torque is small, high temperature does not spread, good adhesion, long-lasting noise reduction, compatible with plastics, will not crack, soften or swell plastics, can significantly reduce the operating noise of plastic gears, low volatilization, extremely long service life, good Excellent water resistance, will not be corroded by acids and alkalis, is non-toxic, odorless, non-irritating, and meets environmental protection requirements. Cleaning fluid
It has the dual functions of valve cleaning and permeability, and is used to loosen and clean valves that are difficult or impossible to open. It cleans and penetrates residual gum, hardening sealants and greases. It penetrates and loosens dirt and rust, extending valve life and performance. Regular use will prevent this. Find the type, size and dosage of your valve from the dosage card. The total usage of your valve is the minimum amount of cleaning fluid to be filled.
.
Divide the total amount by the total number of two seat seal grease nozzles. You should inject valve cleaning fluid into a valve seat through a seal grease nozzle. Then use the same steps to clean the other valve seat. Remember to mark the hydraulic injection gun to record the amount you inject. Measured from the thread of the injection gun in ounces per inch. If the valve is buried, the volume of the nozzle extension must be increased to the calculated ID of the injection volume in oz/ft/., 3/./., 3/
.
Use slow and even pressure. to inject cleaning fluid. This promotes consistent flow rate and even distribution. Rapid filling can cause the cleaning fluid to escape from the edges or from deformations of the trash seal or ring. The trash seal design of many ball valves does not maintain pressure. When operating, a hydraulic manual gun with a pressure gauge can be used. Using this injection gun allows the operator to observe results more accurately than with mechanical or pneumatic equipment.
.
When injecting grease, please keep the pressure at least higher than the pipeline pressure. Generally speaking, for Cameron valves, excessive grease injection pressure seems unsafe. Any time when using external stacking. Dia provides you with the best products with high quality and excellent service. Reasonable prices, guaranteed delivery time, year-round supply, and professional service levels will make your work easier and more efficient! Customers are welcome to call or write to patronize us. Our company will serve you wholeheartedly. Model:
Instructions for use:
Steps for filling the ball valve with valve cleaning fluid
.
If possible, operate the valve to determine its condition. The action of the ball will help dislodge debris and buildup from inside the valve.
.
Place the valve in the fully open or fully closed position.
3.
Determine the number of valve seat sealing grease nozzles. Usually there is one or more nozzles.
When the ring acts as a seal, you must be careful not to overpressure it and push it out. Consult your manufacturer to confirm the precautions for your operation.
.
If you cannot maintain the desired pressure, one possibility is that the injected material is not reaching the problem area and is overflowing into the line. Please consider the following options:

Try injecting sealant to create a temporary seal (the amount required to fit the valve) to plug the leak and give it a chance to maintain pressure. Retry the cleaning procedure until sufficient valve cleaning fluid has been injected.
B
For Cameron ball valves with rotating seats, operate the valve and try to move the problem area closer to the grease injection port.
Note: Some older Cameron ball valves may not have edges or trash seals. This may make it difficult to apply cleaning fluid or lubricating sealant as it cannot be retained.
.
There is no limit on how long cleaning fluid can be retained in the seat area. You will usually find that once you have filled all the sealing grease nipples with cleaning fluid, you can move on to other operations. Although this time greatly depends on the condition of the valve, generally consider a minimum of 3 minutes. Valve cleaning fluid will not damage valves or seals and remains in the valve for extended periods of time.
Note: Remember - valve cleaning fluid does not contain acids, alkalis, or solvents that can harm personnel or equipment.
.
Operate the valve approximately 10 times so that the valve cleaning fluid is applied to the ball through the valve seat. If the valve cannot be fully opened or closed, it should be opened to the maximum possible position. This helps dislodge debris.
.
If necessary, repeat the above process from step 4 onwards.
Grease gun A grease gun is a hand tool used to add grease to mechanical equipment. It can optionally be equipped with an iron gun rod (iron gun head) or a hose (flat gun head) refueling nozzle. If the refueling position is convenient and in a spacious place, an iron gun rod (iron gun head) can be used. If the refueling position is concealed or in a roundabout place, a hose (flat gun head) must be used for refueling. Structure: Grease guns include pneumatic grease guns, manual grease guns, pedal grease guns, electric grease guns, etc. A grease gun consists of four parts: a handle, a gun head, a barrel, and a handle. The grease nozzle can be divided into two types: a pointed mouth and a flat mouth. The accessories are divided into two types: hose and hard tube. The inside of the barrel is made of a leather bowl, spring, and steel balls. , exhaust screws, etc.