Single machine bag dust collector | Single machine dust collector

The structure of the single-machine bag dust collector is mainly composed of the upper box, the middle box, the lower box (ash hopper), the ash cleaning system and the ash discharge mechanism. In addition to the correct selection of filter bag materials, the dust removal system plays a decisive role in the performance of the dust collector. For this reason, the cleaning method is one of the characteristics that distinguishes baghouse dust collectors. There are six specifications for single-machine bag dust collectors:
Type B and Type III, type B is equipped with a dust door, type B is equipped with a drawer, type B has neither a dust door nor a drawer, and a flange is added to the lower part for direct matching according to user requirements. Dust is removed on-site on dust-raising equipment such as warehouse roofs, silos, and belt conveyors, and the dust is directly recovered.
Single-machine bag dust collector
Structural features of the product:
The fan components of the dust collector adopt universal marking fans, which are easy to repair and replace, and use vibration isolation facilities to reduce noise.
The filter material of the dust collector is a cylindrical filter bag, which has good filtration effect and long service life.
The dust cleaning mechanism uses a motor to drive a linkage mechanism to shake the filter bag and clean the inner surface of the filter bag. Its control device is either manual or automatic. The length of cleaning time is left to the user to adjust the time relay.
The dust door adopts two structures: drawer type and dust bucket type, which is very convenient for dust removal.
Things that need to be checked before operation of the air system of single-machine bag dust collector
:
. Purge each pipeline for -1 minute before operation.
. Ensure that the compressed air pipeline is smooth, adjust the air pressure, and then supply air to the equipment air storage bag.
3. Open the drain valve of the gas storage bag, drain all the oil and water, and then close it.
.Check each blowing mechanism one by one to see if there is water accumulation or air leakage.
.Check and confirm that the air path is clear.
The operation of single-machine bag dust collector
can be divided into trial operation and daily operation. First, during trial operation, a single component of the system must be inspected, and then adaptive operation and partial performance testing must be performed. In daily operation, necessary inspections should still be carried out, especially inspections of the performance of single-machine bag dust collectors. Pay attention to the impact that changes in the load of the host equipment will have on the performance of the dust collector. After the machine is started, you should pay close attention to the working condition of the bag dust collector and make relevant records. When the stand-alone bag dust collector is working, the dust-laden air enters the dust box of the dust collector from the bottom of the dust collector. The coarser dust settles downwards by the gravity of the bag dust collector itself and falls into the ash bin. The fine dust is absorbed by various effects. The dust adsorbed on the filter bag accumulates thicker and thicker as time goes by. The resistance of the bag dust collector on the top of the warehouse gradually increases, and the amount of gas processed continues to decrease. In order to keep the stand-alone bag dust collector in an effective working condition, the pressure To keep the loss within a certain range, it is necessary to remove the dust adsorbed on the outside of the bag wall.
The single-machine bag dust collector produced by Botou Keming Environmental Protection Equipment Co., Ltd. is specially designed for the top and bottom of the cement plant. Designed for belt conveying and local dust source dust removal. It can also be used for dust removal from local dust sources in other industries. It has small size, large processing air volume and compact structure. It has the advantages of convenience and reliability. The dust removed from the dust collector can be directly discharged into the bin or fall directly on the belt. The dust-containing gas enters the dust collector from the lower part of the dust collector. After being filtered by the filter bag, the clean air is discharged from the exhaust pipe. fan exhaust. After the dust collector has been working for a period of time, the dust on the filter bag gradually increases, causing the negative force of the filter bag to rise. It needs to be cleaned. After the dust cleaning is completed, the dust collector works normally again.
In terms of technical services of Botou Keming Environmental Protection Equipment Co., Ltd.:
⑴ Promptly provide all technical information and drawings stipulated in the contract to the purchaser, and have the obligation to invite the purchaser to participate in the supplier's technical review when necessary. .
⑵ Our company is responsible for one-stop services from equipment selection, equipment design, manufacturing, installation, debugging and after-sales service.
⑶ Take the initiative to provide the interface requirements and technical condition information of the supporting equipment purchased by the buyer and related to the contract equipment.
⑷ Strictly implement the minutes of meetings or agreements signed by both parties on relevant major issues.
⑸ Free training for demand-side operators on technical issues such as equipment installation, debugging, use and maintenance.
⑹ Complete pre-sales, sales and after-sales services to achieve customer satisfaction.
⑺ After receiving the quality problem information reported by the buyer, our company personnel rushed to the scene within hours to ensure that the service will not stop until the user is not satisfied with the quality.
⑻ Meet the requirements of the purchasing team for spare parts and spare parts at any time.