Small softened water equipment factory direct sales

Generally speaking, the operation of boiler softened water equipment goes through five processes: backwashing, regeneration, slow flushing, and fast flushing of produced water. All processes of different types of equipment are very close, but there may be some additional processes due to differences in actual processes or control needs. Any softened water equipment based on sodium ion exchange is developed on the basis of these five processes.
Since solid granular table salt contains a certain amount of impurities, a large amount of impurities will be deposited at the bottom of the salt tank and block the salt valve, so the impurities at the bottom of the salt tank must be cleaned regularly. When cleaning, you can open the drain valve at the bottom of the salt box and rinse it with clean water until no impurities flow out. The cleaning cycle of the salt box should be determined based on the impurity content of the solid granular salt.
Two main technical indicators
Raw water supply pressure
~
Raw water hardness
/ (calculated in /+/+
Dissolved solids
Outlet water Hardness
/ (calculated as /+/+
Raw water temperature
~℃
Ambient water temperature
~℃
Water production
︿
Resin tank (model
~
Resin quantity
~
Salt bucket volume
~
Regeneration salt
Large grains, cannot be added Iodine, add calcium salt.
Three equipment features
◇High degree of automation, the boiler softened water equipment automatically completes the softening and regeneration cycle process according to the preset program. Daily operation does not require manual operation except adding salt.
◇Small footprint, compact equipment structure, compact and lightweight.
◇Strong corrosion resistance, the tank is made of fiberglass, engineering plastics or stainless steel, which can avoid corrosion of the equipment by the regenerant.
> ◇Reliable performance, stable effluent quality.
◇Flexible model selection, you can choose single tank, double tank, multi-tank system time flow control mode, simultaneous regeneration, alternate regeneration and other operating modes according to your needs.
Four specifications model
Model
Water production volume
Resin tank size
Resin volume
Salt barrel
~
(Min
~
(Inch
~
High
~
~
High
~
~
High
~
~
High
~
~
High
~
~
High
~
~
~
~
What you need to know when choosing the five models
Water consumption per hour (unit) (Subject to the water quality inspection report
Outlet water hardness requirements (unit
Working pressure (unit (, the best is
Continuous water supply time (unit
Ambient temperature and raw water temperature (unit ℃
Six installation requirements
There is no need to specialize in installing the foundation, the foundation is level
If the inlet water pressure is lower than that, a pipeline pump must be installed.
The pipeline must be flushed before use to avoid Impurities clog the valve body and contaminate the resin.
Do not use iodized salt or calcium salt as regenerant. Add salt to the salt tank regularly to ensure the saturated concentration of the brine (the dissolution time should be guaranteed to be no less than six hours.
Seven Later maintenance of equipment
Regularly check the air tightness of the ejector and salt absorption pipeline of the boiler softened water equipment to prevent air leakage and affect the regeneration effect. The water softener should be disassembled once a year, and the upper and lower water distributors and quartz sand pads should be cleaned Impurities in the layer, and check the loss and exchange capacity of the resin, replace seriously aged resin, and use solution to resuscitate iron-poisoned resin.
Ensure that the voltage and current input to the boiler softened water equipment are stable and prevent the electronic control device from burning out. A sealing cover should be installed outside the electronic control device to prevent moisture and flooding. Add solid granular salt to the salt box regularly, and ensure that the salt solution in the salt box is in a supersaturated state. When adding salt, be careful not to sprinkle solid granular salt into the salt well to prevent salt bridges from forming on the salt valve and blocking the salt suction pipeline.
Company official website
Company address Jiugong No., Daxing District, Beijing
Contact person Manager Chang
Contact number
Landline number