Research and produce briquetting machines to overcome all problems h3 Huayi Machinery

The ball press itself should be well grounded to prevent accumulation of static electricity from affecting the ball machine. During installation, the power cord, communication cable and video cable must be correctly connected. When connecting, carefully refer to the installation instructions to confirm the communication method and corresponding pin definitions. Generally, equipment should be installed in the later stages of construction to prevent large amounts of dust from the construction site from intruding into the ball machine and directly affecting its use effect and lifespan.
In addition, the following precautions should be paid extra attention to ensure the normal operation of the ball press. The power supply should not be lower than the nominal value of the input voltage of the ball press. When the nominal value is , the voltage fluctuation should not exceed %. The common working voltage of ball press machine is. There are currently models of ball press machines on the market, which essentially have a transformer built into the ball cover, which supplies power to the ball press machine after voltage transformation. When wiring, emphasis should be placed on separating strong and weak currents to avoid interference from strong currents on weak currents. The internal space of the ball press is limited, and the built-in transformer allows strong and weak currents to coexist, thus affecting weak current signals. In addition, the built-in transformer will increase the heat dissipation burden, thereby increasing the possibility of burning out the built-in circuit. Depending on the on-site environment, local power supply, remote voltage transformation, or centralized power supply can be selected. When providing centralized power supply, the loss of electric energy caused by transmission lines should be fully considered. Choose equipment with larger output power and increase the output voltage appropriately to carry the line voltage drop, such as selecting the output to power a remote ball press.
Has the briquetting machine received enough power to drive? It can be tested with a multimeter. The method is to use a multimeter to measure the voltage of the power cord at one end of the briquetting machine when the load (ball pressing machine) is turned on, and observe whether the voltage is under pressure. Within the scope of dome machine license. What needs special attention is that the power consumed by the outdoor briquetting machine is very different when the heater is started or stopped. When powering the outdoor briquetting machine, the maximum power supply required by the briquetting machine in the worst environment must be considered. . When the mains voltage fluctuation exceeds the range of +% ~ %, an AC voltage stabilizing device should be installed. Can be installed to provide uninterrupted stable power supply. The grounding of the ball press is mainly divided into shell grounding and internal electrical grounding. The shell grounding is mainly used to prevent static electricity accumulation, electrical leakage, etc. The outdoor ball press machine also needs to be equipped with external lightning protection measures. Generally speaking, the shell of the outdoor ball press installed on the pole bracket has naturally formed grounding protection because it is screwed on the metal bracket, so no special treatment is required. The data cable and video cable inside the ball pressing machine have been grounded accordingly. Connect the end of the ball pressing machine to the ground wire to ensure that the equipment is effectively grounded.
The installation of the ball press machine must be waterproofed. For suspended installation, there is a gap between the ball press and the bracket. In the event of rain or snow, water will seep into the interior along the gaps and cause harm. Therefore, waterproof sealing measures should be taken during installation to prevent rainwater from entering the screw interface. The selection of the mounting bracket of the ball press is also very important. It is recommended to use the original bracket. The original bracket fully considers the waterproofing problem, such as using an inclination design to make the rotating end of the ball press slightly higher. Even if water enters the bracket, it will only flow back into the column and not into the ball press. Therefore, if users make their own brackets, they should fully consider waterproof factors. Why are there water droplets in the bracket? Generally speaking, when the temperature is higher during the day, the water vapor in the pole enters the bracket. When the temperature drops at night, water vapor will condense into water droplets and condense along the wall of the bracket. When the bracket is not tilted or tilted in the opposite direction, water droplets will flow into the briquetting machine along the wall, causing harm. To reduce water vapor from entering the bracket, the joint between the bracket and the pole can be sealed with plasticine or silicone.
The heat dissipation problem when the briquetting machine is working must also be considered. Some Huayi award-winning brand briquetting machines on the market do not have outdoor models, so they cannot be directly used outdoors and must be equipped with outdoor shields and other accessories. The standard configuration of the outdoor briquetting machine includes sunshades, heaters, and dual cooling fans, allowing it to adapt to harsh or extreme temperature differences outdoors.
Henan Huayi Machinery Manufacturing Co., Ltd.
Telephone
Mobile
Fax

Email@
Address Wen County Industrial Cluster, Jiaozuo City, Henan Province