Year1
- 工作介质：
- 水或污水
- 工作环境：
- 室外
- 工作时间：
- 5-10min
8903298985 (Mr. Lang)
】【】
< br/> Introduction to the rotary grate decontamination machine. In the front process of sewage treatment, it intercepts and removes small-sized solid particles, floating objects, etc., so that the subsequent treatment process can proceed smoothly. It is an ideal choice for urban sewage and industrial sewage such as textile and papermaking. It is a key equipment for intercepting pollution and removing slag during the treatment process.
Operating Principle and Characteristics Working Principle When the sewage containing floating objects or smaller-sized solid particles passes through the grille, the floating objects and particles and fibers larger than the gap between the grilles, such as aquatic plants, cigarette butts, wood chips, etc. Waste such as flax is intercepted on the rake teeth, and the intercepted matter is lifted up from the grate through the continuously operating rotary mechanical grate. After arriving at the slag discharge port, it relies on the self-weight of the grate slag and the head structure with a special structure. Screen slag falls from the slag discharge port into screen slag conveying equipment such as belt conveyors, screw conveyors, transport trolleys, etc. and is transported to screen slag treatment facilities or sites.
Instructions for use of the electric control box of the rotary grille decontamination machine. The fixed voltage is, the grounding resistance is less than ohms, the grounding should be safe and reliable. Open the door of the electric control box, close the circuit breaker and press the button on the door as needed. When using the button for control, it is best to disconnect the circuit breaker and lock the door. Special control requirements are attached with pictures and instructions.
Maintenance of the electric control box of the rotary grille decontamination machine. Check the electric control box regularly to see if there is an electric shock and loosen it. The dust should be removed. If water is accidentally allowed to enter, stop using it and allow it to dry. Or dry and manage the electrical control box well to prevent outsiders from opening or damaging it and have it maintained and maintained by a full-time electrician.
Features of the rotary grate decontamination machine. The driving device adopts a cycloidal pinwheel reducer to drive the toothed rake to rotate for slag removal and slag removal. It has a compact structure and stable operation. , The whole machine has a simple structure, is not easy to be blocked, is easy to maintain, has low noise and low power consumption. , the operation is simple, can realize fully automatic control of time and liquid level difference, and the operation mode is flexible and convenient. , with mechanical and electrical double overload protection functions. , Reasonable material selection, special anti-corrosion treatment on the surface of the equipment, and long service life of the whole machine.
Preparations before installation of the rotary grille decontamination machine. Before installation, check whether the channel size is qualified. The verticality between the sides of the grille channel and the bottom must not exceed, and the flatness error must not exceed. Check the two steel plates embedded in the walls on both sides of the channel.
Correct the positioning allowable deviation when installing the grille, the plane position deviation, the elevation deviation, the track coincidence deviation of the mechanical grating, the track gauge allowable deviation, the inclination allowable deviation
Before installation, the equipment must be routinely unpacked and accepted, and records must be made. At the same time, the preparation of main materials, construction machinery and labor arrangements should also be checked. Other matching processes have been completed. If there are special requirements, corresponding measures should be taken at the installation site, and the surrounding environment should meet the conditions for equipment installation.
Common faults and troubleshooting methods of the rotary grate decontamination machine) During operation, the motor operates normally but the rake tooth chain does not operate. The cause of the fault was that the equipment was overloaded and the safety pin was cut off. The troubleshooting method is to remove the safety cover and replace the safety pin. 1. To find out the cause of equipment overload, mainly check whether there is any debris blocking the rake chain. If so, remove it before starting the machine. ) The chain slats in the rake chain are worn and must be replaced. The replacement steps are as follows: Insert the crank handle into the rear hole of the motor, and swing the chain slat that needs to be replaced to the inspection hole. , Remove the side plate handle on the access hole. , use two iron rods to block the rake tooth chain. , Replace worn chain slats. , just install the side plate handle.
Routine maintenance and maintenance of the rotary grate decontamination machine) During operation, if there are fiber debris, etc. blocking the rake tooth chain, they should be cleaned in time to avoid affecting the normal operation of the machine. operation. ) When put into normal operation, a grease gun must be used to inject calcium-based lubricating oil into the grease nozzles of each lubricating part every two months. The filling amount is the space between the bearing and the bearing seat. ) The lubricating oil in the reducer must be replaced regularly. Generally, new oil must be replaced after half a month of normal operation of the equipment, and every three months thereafter. Always pay attention to the oil level.
Instructions for ordering rotary grate decontamination machine
,
When ordering, users need to provide the trench width, trench depth, installation angle and rake Tooth clearance, use location conditions, and provide equipment installation plan and elevation diagrams.
,
Equipment rake tooth materials are available in three types: nylon, nylon and stainless steel.
,
The equipment provides a set of equipment control boxes, which are divided into indoor type and outdoor type.
,
Special requirements must be specified in the order contract.
Beiqian Hydraulic Engineering Co., Ltd. was founded on 2019, with a registered capital of RMB 10,000. The company is a professional production and processing enterprise. Its main business is the sales and processing of hoists and gates. Our factory has a total of more than 100 employees. , including many scientific researchers. Since the establishment of our factory, relying on the excellent quality of our products and the good reputation of our manufacturers, we have won praise from our customers and unanimous praise from industry peers. Types of hoists in our factory: manual screw hoist, electric head screw hoist, handwheel screw hoist, screw hoist, two-way door operator, gantry winch, door hoist, hydraulic hoist machine. Types of gates in our factory: cast iron inlaid copper gate, cast iron inlaid copper round gate, cast iron inlaid copper square gate, stainless steel channel gate, stainless steel insert gate, electric insert gate, channel gate, stainless steel gate, cast iron round door, cast iron square door , fiberglass gate. In addition, our factory also produces various cleaning equipment such as rotary grille cleaning machines/decontamination machines, reverse grille cleaning machines/decontamination machines, and circulating rake cleaning machines/decontamination machines. Machine, grab-type cleaning machine, mobile (hydraulic) grab-type cleaning machine. Our factory has a wide range of products for you to choose from, and our service will be until you are satisfied.
National toll-free number 4000319516 mobile phone contact
8903298985 (Mr. Lang)
】【】
WhatsApp
