Chuzhou 4-ton hay mower with conveyor chain

Guangzhou Huaxing Machinery produces and sells silage hay cutters, grass shredders, and grass cutters. They are used to cut all kinds of green grass, hay, cereal straw, rice straw, wild grass, wheat straw, corn straw and other forages. They are currently widely used. The economical mowing equipment used has the advantages of small size, light weight, easy installation, operation and maintenance, and high production efficiency. The production is used to feed cattle, horses, sheep, pigs and other livestock forage and retting, and the straw is returned to the fields. The main purpose is to cut the forage into small pieces of 1 cm to feed cattle, sheep, geese, fish or to make silage feed, etc. The mower is mainly composed of the body, the grass feed roller, the knife holder assembly, the blade, the feeding device, the frame and other parts. Welcome to our company to purchase new mower equipment. Large-scale haymakers can produce tons, tons, tons per hour, and they are always in stock
1. Purpose, scope of use and performance characteristics
Professional haymakers are used to cut grain grass, straw, and wild grass. , wheat straw, corn straw and various fodders, used for feeding cattle, horses, sheep, pigs and other livestock forage and retting, and returning straw to fields.
The length of this machine is adjustable. By changing the position of the V-belt in the cone groove, you can cut grass of two lengths.
According to user needs, the cone wheels of different specifications can be replaced to cut grass of various lengths (the cone wheels are customized with the factory).
. The feeding speed change mechanism of this machine adopts a combination of gear transmission and belt transmission, and all transmission parts
are equipped with high-quality rolling bearings. It has the characteristics of low noise and long service life.
The fixed knife and the movable knife adopt straight cutting edges, which are easy to adjust and sharpen.
2. Main technology and performance parameters
Production efficiency in kilograms/hour
Supporting power in kilowatts (horsepower)
Power supply voltage in volts+
RPM/min
Dimensions**
The length of hay is 2 mm, 3 mm, mm
Material throwing distance is meters
Machine weight is kilograms
3. Structure introduction
The machine is composed of the following mechanisms (see Figure 1)
The feeding inlet mechanism is mainly composed of upper and lower feeding rollers.
The rotary grass cutting mechanism is mainly composed of a moving knife, a fixed knife, and a moving knife body.
, Feed the transmission mechanism of the active cone pulley, the passive cone pulley, the V-belt, and the transmission gear.
, grass cutting transmission mechanism motor wheel, spindle wheel, triangle belt.
, Safety protection device: feeding protective cover (feed port), transmission protective cover, variable speed protective cover, upper protective cover, lower protective cover, discharge port.
4. Sharpening and adjustment of the movable and fixed knives
When this machine leaves the factory, the movable and fixed knives have sharp edges and the clearance has been adjusted. However, during long-term use, some grass or grass may appear. The guillotine efficiency is significantly reduced, indicating that the blade is not sharp and needs to be removed and sharpened.
Open the upper protective cover, loosen the fixing screws of the movable and fixed blades, take out the blade, and sharpen the bevel edge of the blade with a grinding wheel or whetstone (see Figure 2).
Steps to install the movable fixed knife
) First, fix the fixed knife on the fixed knife holder with the fixed knife screw.
) Fix the movable knife on the movable knife body with the movable knife bolt, and adjust the gap between the movable knife and the fixed knife at the same time. The general gap is within the range as needed. After the adjustment is appropriate, tighten the movable knife bolt and tighten the top knife at the same time. The screw and jack screw nut are tightened.
If the V-belt is worn, slips and does not enter the grass, the V-belt should be replaced in time.
When disassembling gears and angle pulleys for maintenance, pay attention to the direction of the thread rotation. The direction of thread rotation is as follows (refer to Figure 1). The driving cone wheel is left-handed and the passive cone wheel is right-handed. The bridge gear shaft is left-handed. The upper roller gear is right-handed and the lower roller gear is left-handed.
If machine parts need to be replaced due to non-human factors due to product quality, the company will not only replace them free of charge, but also bear the cost of packaging and transportation of the parts. (To ensure safety and reputation, you only need to pay a small deposit in advance, and the goods can be shipped quickly, and the balance will be paid when the goods arrive