Type 420 mushroom wood crusher, wet and dry wood crusher, sawdust machine, sawdust machine, branch crusher

Main uses:
. It can cut branches and trunks with a chip diameter
centimeters. It can also be used to cut fibrous stalk-like materials such as bamboo, thatch, corn stalks, and sorghum stalks.
Wood chip machine (
Wood chip machine
,
Wood chip machine
,
Wood chip machine price
,
Wood chip machine equipment< br/>,
Wood chip machine manufacturer
) is a new type of mechanical equipment ideal for the front-end production of wood powder. It can process wood, branches and other raw materials into wood chips at one time, with low investment, It has the advantages of low energy consumption, high productivity, good economic benefits, and easy use and maintenance. This wood chipper is especially suitable for processing wood chips in edible fungus culture media. It mainly consists of a chipping device, a crushing device and a fan. The wood chips after being cut by the chipping device are small in size and can be sent to the crushing device for further crushing without drying. The finished wood chips after crushing are sent to the aggregate location by the fan. The entire equipment is driven by only one motor. It has a simple structure, compact layout, low price, stable operation, low energy consumption, high output, good quality of finished wood chips, and low processing cost. It can also be used for cutting fibrous stalk-like materials such as bamboo, thatch, corn stalks, and sorghum stalks.
. . 1. Working principle:
It adopts blade cutting and high-speed airflow impact and collision dual crushing functions, and can complete the micro material sorting and processing process at the same time. During the cutting and crushing process of the blade, the rotor generates high-speed airflow, which rotates in the cutting direction of the blade. The material is accelerated in the airflow, and the repeated impact causes the material to be double crushed at the same time, accelerating the crushing rate of the material.
Machine installation and maintenance:
Machine maintenance is an extremely important and regular task. It should be closely coordinated with extreme operation and maintenance, and full-time personnel should be on duty for inspection
/> Wood chip machine
,
Wood chip machine
,
Wood chip machine price
,
Wood chip machine equipment
,
Wood chip Machine manufacturer
2. Machine maintenance:
The shaft of the bearing sawdust machine bears the entire load of the machine, so good lubrication has a great relationship with the life of the bearing, which directly affects the service life and performance of the machine. The operating rate therefore requires that the injected lubricating oil must be clean and the seal must be good. The main oil filling point of this machine is the rotating bearing, roller bearing, all gears, movable bearings, sliding planes
, and newly installed wheel hoops that are prone to loosening and must be inspected frequently.
Pay attention to whether all parts of the machine are working normally
Pay attention to check the degree of wear of easily worn parts, and replace worn parts at any time
The bottom shelf plane where the movable device is placed should be cleaned of dust, etc. When the machine encounters materials that cannot be broken, the movable bearing cannot move on the chassis, resulting in a serious accident.
If the bearing oil temperature rises, stop the machine immediately to check and eliminate the cause.
If there is any impact sound during operation, stop the machine immediately for inspection and eliminate it
3. Installation and test run
:
The equipment should be installed on a horizontal concrete foundation and fixed with anchor bolts.

When installing, pay attention to the verticality of the main body to the horizontal.

After installation, check whether the bolts in various parts are loose and whether the main machine compartment door is tight. If so, please tighten it. solid.

Configure the power cord and control switch according to the power of the equipment.

After the inspection is completed, conduct a no-load test run. If the test run is normal, production can begin.
. . 4. Operation:
. .
Turn on the power and see if the steering is correct.
.
When installing and replacing the tool, the knife edge extends out of the cutterhead plane, and then tighten the bolt. If the thread of the pressure bolt is found to be worn, it should be replaced immediately to prevent damage to the cutterhead nut.
.
To change the expansion and contraction of the knife, the length of the extended knife must be consistent.
.
When the particles cannot reach the ideal level by adjusting the knife length, replace the sieve with different apertures.
.
It is strictly forbidden to put firewood containing stones and nails into the machine to prevent damage to the knife and internal parts.
.
Pay attention to check the hammer bolts. If they are found to be loose, tighten them immediately. If the hammers and bolts are seriously worn, they should be replaced.
. .
. . 5. Maintenance:
. .
Add lubricating oil to the friction position regularly to ensure mechanical performance and service life.
. .
After the machine is used, it should be disassembled and placed, and the sawdust in the machine should be cleaned to avoid affecting future use and production.
.